Used Lab Equipment

Features:

Thermo Scientific Forma Fury laboratory glassware dryer

Specifications:

• Temperature Range : +50C above ambient to +200C
• Interior Construction : Stainless steel
• Interior Volume : 32.6 cu.ft.
• Interior WxHxF-B : 33in. X 55in. X 31in.
• 4 stainless steel shelves.
• 208/230V
• 50/60Hz
• 14.5A
• 1PH

The Mini Spray Dryer B-290 is the laboratory equipment of your choice for the quick and gentle drying to powder of liquid end products. The impressive features of the Spray Dryer include its efficient performance with very short set-up times, an effective integrated nozzle cleaning mechanism and a high degree of flexibility thanks to the different cylinder geometries. Whether the requirement is the gentle drying of natural product dyestuffs, the isolation of highly effective pharmaceutical active agents, or the micro-encapsulation of aromas – the B-290’s outstanding features greatly extends the number of applications that are possible with a  spray drying process

Includes:

• Buchi B-290 Mini Spray Dryer w/ Glassware (as shown)
• Standard Glassware
• Advanced Cylinder Shield
• New Nozzle Assembly
• Aspirator Recently Cleaned

Specifications:

• Power consumption: max. 2900 W
• Connection voltage: 200-230 V ± 10 %
• Frequency: 50/60 Hz
• Evaporating capacity: 1.0 l/h H2O, higher for organic solvents
• Airflow: max. of 35 m3/h
• Motor control: Frequency converter
• Max. temperature input: 220 °C
• Heating capacity: 2300 W
• Heating control: PT-100, fuzzy logic, control accuracy ± 3 °C
• Interface: Serial port RS-232 for all parameters
• Spray gas: Compressed air or nitrogen / 200 - 800 l/h; 5 - 8 bar
• Nozzle tip diameter: 0.7 mm standard, other sizes 1.4 and 2.0 mm available
• Possible particle diameter range: 1 - 25 μm
• Mean residence time: 1.0 - 1.5 sec.
• Pollution degree: 2
• Installation category: II
• Dimensions (W x H x D): 65 x 110 x 70 cm
• Weight: 46 kg

Features:

The Savant SC 200 is a Speed Vac Centrifugal Evaporator with radiant cover and rotor

Specifications:

• Outside Dimensions: L 20" x W 28.5" x H 19"
• Inside Dimensions: 16" Diameter x H 5"
• Port - Vent Diameter: 2.5" Diameter Rotor Buckets (x8)

Description:

The Console Drives are highly featured yet easy to operate Masterflex L/S pump drives, These drives are self contained compact unites that include a drive motor and all operating controls. The keypad is laid out on a sloped front panel for ease of control and for quick and easy indication status. A digital display provides a continuous indication of flow rates, actual rpm or percentage of maximum rpm.

Specifications:

• Maximum Speed: 100 rpm
• Minimum Speed: 1.6 rpm
• Operating Temperature: 0°C to 40°C
• Storage Temperature: -10°C to 60°C
• Chemical Resistance: Exposed material is paint, plastic, aluminum, and vinyl
• Line Voltage Limits: 90 to 130 V AC, 50/60 Hz
• Dimensions (L x W x H): 11.5 x 7 x 7 in. (29.2 x 17.8 x 17.8 cm)
• Weight: 15 lbs. (6.8 kg)

Specifications:

• Number of solvents: Up to four: in any combination of two: Al or A2 and Bl or B2
• Solvent storage: Solvents Tray accommodates up to four chromatographic solvents, two Sample Manager wash solvents and one Binary Solvent Manager seal wash solvent
• Solvent conditioning: Vacuum degassing (Six-channel): one channel per solvent, and two channels for Sample Manager wash solvents
• Operating flow rate range: 010 to 2.000 mL/min, in 0.001 mL increments
• Compressibility compensation: Automatic and continuous
• Effective system delay volume: <120 ulL, independent of system backpressure (with standard 50-ilL mixer installed)
• Plunger seal wash: Integral, active, programmable
• Gradient profiles: Eleven gradient curves [including linear, step (2), concave (4), and convex (4)]
• Wet prime: Automatic
• Maximum operating pressure: 15,000 psi up to 1 mL/min, 9,000 psi up to 2 mL/min per pump, not more than 15,000 psi total
• Composition accuracy:
  • ±0.5% absolute (full scale) from 5 to 95% of flow rates
  • from 0.5 to 2.0 mLlmin (Contact Waters for conditions used)
• Composition precision: 0.15% RSO or ±0.04 min SO, whichever is greater, based on retention time
• Flow precision: 0.075% RSO or ±0.02 min SO, six replicates, based on retention time or volumetric measures (0.500 to 2.000 ml/min)
• Flow accuracy: ± 1.0% at 0.5 mL/min with degassed methanol, per Waters AQT/SystemsQT protocol
• Primary wetted materials: 316 stainless steel, UHMWPE, sapphire, ruby, FEP, PTFE, ETFE, diamond-like coating, PEEK and PEEK alloys, titanium alloys
• Unattended operation: Leak sensors, full diagnostic data captured through console software

The Waters ACQUITY UPLC H-Class System delivers the flexibility of quaternary solvent blending with the advanced performance of UPLC® separations. The system's holistic design is targeted for routine analysis and method development use and is perfectly suited for running both HPLC and UPLC applications while still realizing the improved resolution and sensitivity of UPLC separations.

Includes:

• TUV Detector (PDA Detector $1000 additional)

• Sample Manager - FTN

• Column Manager to control up to 4 Columns
• Quaternary Solvent Manager
  • 15,000 psi up to 1.0 mL/min,
  • 9000 psi up to 2.0 mL/min
• Computer Loaded with Empower

Specifications:

• Dwell volume (total system): <400 ~L (includes standard 100 ~L mixer)
• Integrated leak management: Leak sensors, as standard, and safe leak handling
• Quantum synchronization: Injection synchronization between pump and sample manager enhances retention time reproducibility
• Set table flow rate range:
  • 01 0 to 2.000 mLlmin, in 0.001 mL increments (firmware version 1.5x and earlier)
  • 010 to 2.200 mL/min, in 0.001 mL increments (firmware version 1.60)
  • 001 to 2.200 mLlmin in 0.001 mL increments (firmware version 1.65 and later)
• Maximum operating pressure:
  • 15,000 psi up to 1.0 mL/min, 9000 psi up to 2.0 mL/min (firmware version l.5x and earlier)
  • 15,000 psi up to 1.0 mL/min, 7800 psi up to 2.2 mL/min (firmware version 1.6x and later)
• pH range: 2 to 12
• Unattended operation: Leak sensors and safe leak handling, full 96-hour diagnostic data display through console software
• Cycle time: <30s Inject to Inject

Specifications:

• Number of sample plates: Total of two plates, expandable to up to 22 plates with optional Sample Organizer (see below):
  • 96 and 384 microtiter plates
  • 48 position 2.00-mL vial plates
  • 48 position 0.65-mL micro-centrifuge tube plates
  • 24 position 1.50-mL micro-centrifuge tube plates
• Maximum sample capacity: 768 in two 384-well plates; expandable to up to 8,448 samples with optional Sample Organizer
• Number of sample injections: 1 to 99 injections per sample
• Injection volume range: 0.1 to 50.0 iJL, in 0.1 iJL increments, partial or full loop mode; 10ul loop is standard; 1, 2, 5, 20, and 50-uL loops also available
• Sample delivery precision(full loop injection mode): < 0.3% RSO, full loop, standard lO-iJL loop (default wash/purge conditions), per Waters AQT/SystemsQT protocol
• Sample delivery precision(PLNO injection mode): < 1% RSO within 20% to 75% of loop volume for 1, 2, 5, 10, 20, and 50-iJL loops, UV detection
• Injector linearity: > 0.999 coefficient of deviation (from 20% to 75%, partial loop overfill mode (PLNO injection mode), per Waters' AQT/SystemsQT protocol
• Sample temperature control:0 to 40.0 ·C, settable in 0.1 ·C increments (assumes an ambient temperature of 25.0 ·C). At an ambient temperature of 21.0 ·C or lower the sample manager will maintain the temperature of the sample compartment down to 4.0 ·C with a tolerance of -2.0/+6.0 ·C, when configured with the maximum number of vials and/or plates
• Injection cycle time:
  • < 15 sec between multipe injections with "load ahead" enabled
  • 30 sec with single weak wash, lO-iJL loop, pressure assist mode
• Sample probe: XYZZ based needle-in-needle design
• Minimum sample required: 5 uL residual, using maximum recovery 2-mL vials (zero offset)
• Wash solvents: Two degassed: strong solvent and weak wash solvent, programmable to suit application
• Sample carryover: < 0.005% or < 2.000 nL, whichever is greater
• Advanced operations: Loop off-line mode, load ahead
• Unattended operation: Leak sensors, full diagnostic data control captured through console software
• Primary wetted material: Titanium alloy, 316 stainless steel, fluoropolymer, fluoroelastomer, PPS alloy, PEEK alloy, PPS, PEEK, OLC coating, gold

The ACQUITY UPLC TUV Detector is a tunable, dual wavelength ultraviolet/visible (UV/Vis) detector that offers optimal linearity, resolution, and sensitivity for UPLC/UV separations.  It features uniquely designed, patented, light-guiding flow cell technology, low-noise performance (6 μAU), and support for data rates up to 80 Hz.  The ACQUITY UPLC TUV Detector, coupled with our innovative ACQUITY UPLC Column chemistries and separations modules, leverages ultra-low dwell volume and low-noise, high-speed detection to bring productivity, sensitivity, and resolution that are unprecedented in HPLC techniques being used in the laboratory today.

Specifications:

• Wavelength range: 190 to 700 nm
• Wavelength accuracy: ±1 nm
• Linearity range: Deviation at 2.5 AU ≤5%, propylparaben, at 257 nm
• Baseline noise:6 x 10^-3 AU, at 230 nm, 10 mm shunt cell, 1.0 second filter time constant
• Drift: ≤5.0 x 10^-4 AU/hour/°C at 230 nm
• Sampling rate: Up to 80 points/s
• Unattended operation: Leak sensors, full diagnostic data captured through console software
• Light source: Prealigned, intelligent technology Deuterium lamp
• Flow cell design: Light-guiding UPLC flow cell with intelligent chip technology
• Path length: 10 mm (analytical flow cell)
• Cell volume: 500 nL (analytical flow cell)
• Pressure limit: 1000 psi (all flow cells)
• Wetted materials: 316 stainless steel, fused silica, Teflon AF, PEEK (analytical flow cell)
• Optical bandwidth: 5 nm

Bruker AMX-300 Nuclear Magnetic Resonance Spectrometer with the "piano" style console and an unshielded Oxford 300MHz magnet. The magnet was de-energized about five years ago. All of the kits for moving the magnet are included.  

This is a 2-channel system with a solids accessory rack with high power 1H and X transmitters. Three probes included (plus a Doty solid state probe): a 5mm 1H inverse probe, a 10mm BB, and a standard bore magic angle solids probe (7 & 4mm stators).  

Description:

These cost-effective vertical laminar flow and horizontal laminar flow workstations feature the Clean-Ceil fan filter module, which utilizes a HEPA filter that is 99.99% efficient for all particles >=0.3µm. The workstations may be used as either benchtop or console units. They incorporate a modular design approach that allows the user to customize a workstation by choosing the optional accessories necessary to meet individual requirements. The workstations come complete with aluminum support frame, clear Plexiglas side panels, 40% efficient ASHRAE-rated prefilter, white plastic laminate back panel (vertical model only, filter is on top), or clear Plexiglas top panel (horizontal model only, filter is on back).

Specifications:

• Dimensions (D x H x W): 21” x 22” x 46”
• Electrical: 115 V, 60 Hz
• Air velocity: 90 ±20 fpm

Features include:
• Ability to store 3 separate user-programmed cycles
• RS 232 interface for printer or PC communication
• Delayed start and stop function
• Time range up to 99 hours and 59 minutes
• Digital temperature readout
• User-friendly interface
• 304 stainless steel chamber
• Working temperature from 5°C over ambient to 250°C (300°C as option)
• 5” of insulation for low heat radiation
• Natural low velocity air flow
• Easy open door latching system
• Attractive look and design
• Removable air distribution plates (no tools required)
• Two internal wire shelves included

Convincingly cost saving laboratory dryer with a 111-liter chamber volume. Natural fine air flow in the chamber, noiseless operation. High-quality and safe drying, heating and tempering of common laboratory materials in laboratories and industry. Wide range of optional equipment and accessories and output option for a printer or PC connection.

Specifications:

• Interior of stainless steel material: volume (111 l), depth (390 mm), width (540 mm), height (530 mm)
• External dimensions: depth (640 mm), diameter of the air branch outer/inner (52/49 mm), width (760 mm), height (860 (N) mm)
• Weight: 87 kg (gross)
• Heat emission at 250 °C: 760 W
• Air exchange speed at 250 °C: 12 per hour
• Working Temperature (from 5°C ambient temp): 250 °C

Features include:
• Ability to store 3 separate user-programmed cycles
• RS 232 interface for printer or PC communication
• Delayed start and stop function
• Time range up to 99 hours and 59 minutes
• Digital temperature readout
• User-friendly interface
• 304 stainless steel chamber
• Working temperature from 5°C over ambient to 250°C (300°C as option)
• 5” of insulation for low heat radiation
• Natural low velocity air flow
• Easy open door latching system
• Attractive look and design
• Removable air distribution plates (no tools required)
• Two internal wire shelves included

Convincingly cost saving laboratory dryer with a 22-liter chamber volume. High-quality and safe drying, heating and tempering of common laboratory materials in laboratories and industry. High operation comfort, precise temperature regulation and short times of temperature recovery in the chamber after the door opening.

Specifications:
• Interior of stainless steel material: volume (22 l), depth (320 mm), width (240 mm), height (295 mm)
• External dimensions: depth (580 mm), diameter of the air branch outer/inner (52/49 mm), width (406 mm), height (604 (N) mm)
• Weight: 36 kg (gross)
• Heat emission at 250 °C: 300 W
• Air exchange speed at 250 °C: 6 per hour
• Working Temperature (from 5°C ambient temp): 250 °C

Features include:
• Ability to store 3 separate user-programmed cycles
• RS 232 interface for printer or PC communication
• Delayed start and stop function
• Time range up to 99 hours and 59 minutes
• Digital temperature readout
• User-friendly interface
• 304 stainless steel chamber
• Working temperature from 5°C over ambient to 250°C (300°C as option)
• 5” of insulation for low heat radiation
• Natural low velocity air flow
• Easy open door latching system
• Attractive look and design
• Removable air distribution plates (no tools required)
• Two internal wire shelves included

Convincingly cost saving laboratory dryer with a 222-liter chamber volume. High-quality and safe drying, heating and tempering of common laboratory materials in laboratories and industry. High operation comfort, precise temperature regulation and short times of temperature recovery in the chamber after the door opening. Wide range of optional equipment and accessories and output option for a printer or PC connection.

Specifications:

• Interior of stainless steel material: volume (222 l), depth (540 mm), width (540 mm), height (760 mm)
• External dimensions: depth (790 mm), diameter of the air branch outer/inner (52/49 mm), width (760 mm), height (1090 (N) mm)
• Weight: 116 kg (gross)
• Heat emission at 250 °C: 990 W
• Air exchange speed at 250 °C: 5 per hour
• Working Temperature (from 5°C ambient temp): 250 °C

Features include:
• Ability to store 3 separate user-programmed cycles
• RS 232 interface for printer or PC communication
• Delayed start and stop function
• Time range up to 99 hours and 59 minutes
• Digital temperature readout
• User-friendly interface
• 304 stainless steel chamber
• Working temperature from 5°C over ambient to 250°C (300°C as option)
• 5” of insulation for low heat radiation
• Natural low velocity air flow
• Easy open door latching system
• Attractive look and design
• Removable air distribution plates (no tools required)
• Two internal wire shelves included

Convincingly cost saving laboratory dryer with a 404-liter chamber volume. Natural fine air flow in the chamber, noiseless operation. Standard model with a Fuzzy-Logic microprocessor control system; control elements situated on a foil keyboard, process information indicated on a LED display

Specifications:

• Interior of stainless steel material: volume of (404 l), depth (540 mm), width (540 mm), height (1410 mm)
• External dimensions: depth (790 mm), diameter of the air branch outer/inner (52/49 mm), width (760 mm), height (1910 (K) mm)
• Weight: 175 kg (gross)
• Heat emission at 250 °C: 1940 W
• Air exchange speed at 250 °C: 4 per hour
• Working Temperature (from 5°C ambient temp): 250 °C

Features include:
• Ability to store 3 separate user-programmed cycles
• RS 232 interface for printer or PC communication
• Delayed start and stop function
• Time range up to 99 hours and 59 minutes
• Digital temperature readout
• User-friendly interface
• 304 stainless steel chamber
• Working temperature from 5°C over ambient to 250°C (300°C as option)
• 5” of insulation for low heat radiation
• Natural low velocity air flow
• Easy open door latching system
• Attractive look and design
• Removable air distribution plates (no tools required)
• Two internal wire shelves included

Convincingly cost saving laboratory dryer with a 55-liter chamber volume. Standard model with a Fuzzy-Logic microprocessor control system; control elements situated on a foil keyboard, process information indicated on a LED display. Wide range of optional equipment and accessories and output option for a printer or PC connection.

Specifications:

• Interior of stainless steel material: volume (55 l), depth (390 mm), width (400 mm), height (350 mm)
• External dimensions: depth (640 mm), diameter of the air branch outer/inner (52/49 mm), width (620 mm), height (680 (N) mm)
• Weight: 66 kg (gross)
• Heat emission at 250 °C: 590 W
• Air exchange speed at 250 °C: 8 per hour
• Working Temperature (from 5°C ambient temp): 250 °C