Used Lab Equipment

The Decloaking Chamber is a programmable benchtop pressure cooker intended for laboratory use. It is programmed to allow the precise pressurized heating necessary for antigen retrieval and also has the capability to perform at a variety of temperatures ranging from 37 °C to 125 °C. The Decloaking Chamber is an excellent tool for heat-induced epitope-retrieval (HIER) methods. The proper use of heat and pressure in conjunction with the appropriate buffer solutions is of the utmost importance for consistent immunohistochemistry (IHC) staining. The Decloaking Chamber is designed to optimize and standardize antibody staining procedures and has been engineered to pass strict laboratory safety requirements. Temperature, pressure and pH can be monitored and recorded with the Decloaking Chamber to produce consistent staining, which will reduce repeat testing and false negatives.

Specification:

• Dimensions (W x D x H): 31 x 29 x 28
• Pan Capacity: 3.2 liters
• Weight: 3.7 (8.18 lbs)

Specification:

• Temperature Range: -73°C to +175°C
• Control Tolerance: ±0.2°C (Measured at the control sensor after stabilization)
• Uniformity: ±0.5°C (Variations throughout the chamber after stabilization)
• Heat-up Transition Time: 5°C/minute typical

• Refrigeration and Heating System

• High Stage Refrigerant: R-404A (Dupont HP-62)
• Low Stage Refrigerant: R-508B (Dupont SUVA-95)
• Compressors: 1/2 HP x 1/3 HP Copeland hermetic compressors in a cascade configuration.
• Condenser: Air cooled
• Heat of Rejection: 4,000 BTUH (maximum rated chamber load at maximum cooling rate from high temperature soak)
• Heater Power: 600 Watts
• Temperature Controller: 256 step, 40 profile, ramp and soak programmable memory. RS-232/485 interface.
• Limit Controller: Independent high and low temperature limits. Triggers an audible alarm and shuts down the chamber.
• Power Requirements: Input voltage - 120 V nominal (110 to 126 VAC), 60 Hz, 1 PH, maximum current draw 15 A, recommended minimum service 20 A
• Inside Dimensions (W x H x D): 16 x 12 x 14 in. (1.55 cubic feet) / 406 x 305 x 353 mm (44 liters)
• Outside Dimensions (W x H x D): 24 x 61 x 26 in. (610 x 1549 x 660 mm)
• Chamber Weight: 300 pounds

Rugged, high-performance baths maintain water temperature from ambient to 95°C or 99.9°C (depending on model) with ±0.2°C uniformity (at 37°C) and ±0.1°C control resolution (at 37°C) with stainless-steel gable cover.

Includes: Gable cover: stainless steel for all; Diffuser shelf

• Choice of analog or digital temperature control
• Chamber capacities ranging from 1.5 to 43L
• Front-mounted controls simplify operation
• Overtemperature safety circuitry prevents thermal runaway
• Dual-chamber models have independent controls for operating at different temperatures

Specifications

• Temperature Control Resolution: ±0.1°C†
• Temperature Uniformity: ±0.2°C†
• Temperature Range: Ambient to 99.9°C
• Chamber: Stainless steel
• Cabinet: Epoxy powder-coated stainless steel
• Capacity: 3.2 gal. (12L)3
• Reservoir: L x W x D: 11.5 x 12.5 x 6 in. (29.2 x 31.7 x 15.2cm)
• Weight: 40 lb. (18.1kg)
• Electrical Requirements: 120V 50/60Hz

Specifications:

• Humidity Control
• Temperature Range: 0°C to 60°C
• Chamber Volume: 29 Cubic Feet / 821.2 Liters
• Temperature Uniforimity: ±0.3°C at 37°C
• Temperature Sensitiviy: ±0.1°C
• Chamber Dimensions (HxWxD):  60” x 31” x 27”
• Exterior Dimensions: (HxWxD):  88.5” x 38” x 32”
• Weight: 1040 LBS
• Capacity: 29 cu. ft. (821.2L)
• Voltage: 208/220V 60 Hz, 15.0A
• 4-wire power cord (including ground)
• NEMA 14-20P plug
• 6 solid stainless-steel shelves
• Exterior D x W x H: 32 x 38 x 88.5 in. (81.3 x 96.5 x 224.8cm)
• Interior D x W x H: 27 x 31 x 60 in. (68.6 x 78.7 x 152.4cm)

Broad Range of Features and Controls

• Wide temperature range of 0° to 60°C enhances the flexibility of the unit
• Relative humidity control via steam generator from above ambient to 95% at 37°C†
• Sophisticated digital controls
• Programmable ramp and soak cycles for temperature and RH†
• Durable cabinets feature true laminar airflow through side plenums for extremely tight uniformity
• Phenolic-coated evaporator for use in applications that create corrosive byproducts
• Manual control of defrost and refrigeration cycles
• Visible/audible safety alarms alert to over- and undertemperature conditions, deviation of humidity from set parameters (except Model 3920)

Durable Construction

• Cold-rolled steel, powder-coated cabinet
• 0 in. (5.1cm) thick, CFC-free, foamed-in-place polyurethane insulation
• Stainless-steel interior
• Solid stainless-steel adjustable shelves
• Directed horizontal airflow system for excellent uniformity
• Locking swivel casters ensure easy mobility during installation and cleaning
• Leveling feet provide stability and added safety in the lab

These accurate and reliable chambers are ideal for long-term high temperature and relative humidity (RH) testing. Designed to provide a wide range of environments, these units are suitable for both industrial and biotechnology specification testing, specifically continuous-duty projects.  All models are equipped with a gentle horizontal air flow system, which ensures stable, top-to-bottom temperature and RH uniformity. Low temperature models 9005L and 9010L feature CFC-free refrigerant. Relative humidity range may vary depending on temperature set point.  Digitally set, microprocessor temperature and humidity controllers allow precise setting with direct digital read-out in degrees and percentage RH.  The over-temperature safety control prevents possible damage to samples or equipment. A vapor generator compresses moisture and injects it into the chamber to provide controlled humidification. Automatic water level control maintains liquid level in humidity reservoir. Pressure coupling allows for easy hook-up of in-line plumbing or a carboy of distilled water. All units feature interior drain.

Specifications:

• Temp range: 40 to 70°C
• Capacity: 9 cu ft.
• Humidity range: 5% above ambient to 95% RH.
• Inside dimensions: 30"W x 20"D x 30"H.
• Interior: Stainless steel.
• Shelves: 2 shelves

Designed to culture dozens, and even hundreds, of samples on up to four independently controlled shakers. Powerful heater and fan provide rapid heat-up capability and temperature uniformity, and humidity control that minimizes evaporation.

Specifications:

• Speed: 25 to 400 RPM
• Temperature Range: 20°C below ambient to 60°C
• Temperature Gradient: ±0.5°C
• Humidity Control: 90% between 37°C and 45°C, 85% between 25°C and 36°C
• Dimensions: 55” x 30.5” x 78.5” in (W x D x H)
• Orbit Diameter: 1 or 2 in

Specifications:

• Digital Controller
• 1000W heater
• Temperature range ambient +5C up to 200C
• 6L chamber capacity

Specifications:

• Type: Bench-top
• Operating Temp: Ambient +5° to 45°C
• Chamber Volume: 1.32 cubic feet (37 liters)
• Chamber Dimensions: 13.44" x 12.68" x 12.65"
• Power Required: VAC 120, optional 240
• Weight: 11.9 kg (26 lb)
• Display/Insulation: Fiberglass

Description:

The VWR 1500E Incubator is a 1 cubic foot incubator with a temperature range of 5° above ambient to 70°C. Temperature uniformity is ±0.5° at 37°C. The VWR 1500E series was designed for routine small incubation loads utilizing gravity convection. The stainless steel chamber design minimizes heat loss while maximizing uniformity.

Specifications:

• Temperature Range: Ambient +5° to 70°C
• Temperature Uniformity: ±0.5° at 37°C
• Number of Shelves: 2
• Exterior Dimensions (W x H x D): 16 x 22 x 16 in
• Electrical Requirements: 120V, 50/60Hz, 3.0A

Heating elements in all three walls, bottom, and door create a warm air jacket around the inner chamber to guarantee superior temperature uniformity with no hot spots. Warm air jacket design also provides quick temperature recovery—and there’s a full-length inner glass door for viewing specimens without disturbing the chamber atmosphere. No need to worry about heater element damage from spills either—the inner chamber is tack-welded, and the low-watt density heating elements are safely isolated from the work chamber.

Microprocessor controlled for easy keypad set and calibration. Temperature display may be calibrated to match a secondary thermometer. For over-temperature protection, a second, independent safety controller can be preset and has visual alarm when activated. All units are stackable without the need for spacer racks. Features through-wall access port for chart recorder. A UL-approved, vapor-tight electrical outlet is inside the sealed chamber. Adjustable leveling feet compensate for uneven surfaces. Shelves adjustable in 1.3cm (¹/₂") increments.

Features:

• Exclusive Hybrid Heating System
• Microprocessor Control
• Easy Keypad Set and Calibration
• Over-Temperature Protection
• Access Port
• Heated Outer Door
• Interior Electrical Outlet
• Stainless Steel Interior and Shelves
• Temperature Range: 5° above ambient to 60°C
• Uniformity: ±0.25° at 37°C

Designed to meet general purpose needs of a wide range of laboratory applications, the Thermo Scientific Precision 180 Water Bath provides consistent results. Sturdily constructed this water bath’s chamber is fashioned from a single sheet of easy to maintain, corrosion and chemical resistant stainless steel, and is housed in a epoxy powder coated steel exterior. The interior chamber has a 1.5 L (0.4gal) capacity. Controls for this analogue water bath are mounted on the front for easy access, with a hydraulic thermostat, making it an ideal choice when temperature set points wont vary much. 

Specifications:

• Capacity: 1.5 L
• Dimensions: 14 x 15 x 5 in
• Weight: 33 lbs
• Temperature: 100°C
• Temperature Uniformity: +/- 0.2°C

Specifications:

• Chamber Capacity: 0.4 gallon / 1.5 liters
• Temperature Display: 0 ÌŠ to 100 ÌŠ C (Thermometer)
• Maximum Temperature: 95.0 ÌŠC
• Temperature Uniformity: ±0.2 ÌŠC at 37 ÌŠC
• Temperature Sensitivity: ±0.1 ÌŠC at 37 ÌŠC
• Electrical Requirements: 120 V, 225 W, 50/50 Hz
• Dimensions (L x W x H): 6 x 11.5 x 2 in

Specifications:

• Temperature Range (Metric): Ambient to 95° or 99°C
• Voltage: 120V
• Cabinet Material: Epoxy powder-coated stainless steel
• Chamber Material: Stainless steel
• Depth (English) Interior: 6 in.
• Depth (Metric) Interior: 15.2cm
• Height (English) Exterior: 9.75 in.
• Height (Metric) Exterior: 24.8cm
• Hertz: 50/60Hz
• Length (English) Exterior: 16.2 in.
• Length (Metric) Exterior: 41cm
• Temperature Resolution: ±0.1†°C
• Temperature Uniformity: ±0.2°C
• Wattage: 300w
• Width (English) Exterior: 8 in.
• Width (English) Interior: 6 in.
• Width (Metric) Exterior: 20.3cm
• Width (Metric) Interior: 15.2cm
• Amperage: 2.5A
• Capacity (Metric): 5.5L
• Control: Analog
• Length (English) Interior: 11.5 in.
• Length (Metric) Interior: 29.2cm
• Operating Temperature: 99.9°C
• Dimensions (L x W x H) Exterior: 16.2 x 8 x 9.75 in. (41 x 20.3 x 24.8cm)
• Electrical Requirements: 120V 50/60Hz
  
  

The VWR Signature Reach-In Incubators are supplied with six shelves capable of supporting the weight of benchtop instruments. The air jacket design and heated outer door allows for uniform heat throughout the incubators. They incorporate a microprocessor controller to achieve precise temperature uniformity. An independent, secondary temperature controller offers the added security of over temperature protection. The chamber floors are reinforced to support roller apparatus or shakers.
Specifications:

• Exterior Dimensions: 41 x 32 x 88 in

• Interior Dimensions: 35 x 26 x 76 in

• Power Requirements: 120V, 50/60Hz, 16A

• Temperature Range: 5° above ambient to 70°C

• Volume: 40 cubic feet

• Carbon Dioxide Range: 0 - 20%