Used Lab Equipment

Features:

Electronic Pipettes rack

This Electronic contact thermometer contains 3 patented operating modes of IKA, with optimized PID control, RESET function and includes a stainless steel sensor. It ensures perfect temperature control without overshooting the set temperature, even in the case of quick heating.

Specifications:

• Temperature Range: -50 °C - 450 °C
• Immersion Depth Max:200 mm
• Dimensions: 82 x 83 x 22 mm
• Weight: 2 kg
• Permissible Ambient Temperature:0 - 60°C
• DC Voltage:8 - 16 V
• Current Consumption: 15 mA

Description:

• Vibration-free, magnetically coupled beveling surface
• Abrasive surface optically flat to a half wave (250 nm)
• Finest abrasive surface commercially available
• Synchronous clock motor insures stable rotation rate
• 7 lb steel base plate adds additional dampening
• Integrated LED lamp
• Robust micromanipulator controls bevel angle and advancement

Specifications:

• Beveling Range: 0.1µm through 100 µm finished electrodes depending on abrasive plate used
• Grinding Surface Variation: less than 1.0 µm
• Grinding Speed: 60 RPM
• Beveling Angle Range: 5-90 degrees
• Dimensions: 19” x 9” x 8” (48 cm x 22 cm x 20 cm)
• Weight: 30 lbs. (14 kg)
• Electrical: 110-120 V / 200-240 V, 50/60 Hertz
• Certificates: RoHS, CE

Specifications:

• Volume: 5-100 mL

Experience a new dimension of electronic pipetting with the Eppendorf Easypet® 3. The latest technological developments give you complete speed control with the utmost precision. The lightweight, well-balanced Easypet 3 has been designed considering all ergonomic findings to fit comfortably in your hand and matches its shape to allow for fatigue-free pipetting.

Specifications:

• Capacity: 0.1 - 100 mL
• Charge time: Less than 3 hours
• Cordless Run Time: Dispense approx. 2,000 times with a 25 ml pipette

Specifications:

• Volume: 5-100 mL

Specifically designed to minimize operator fatigue, the Portable Pipet-Aid XP is smaller and lightweight. It accepts most pipettes from 1 to 100 mL.

Each pipette filler and pipet dispenser button has three speeds, (F) Fast, (M) Medium, (S) Slow. The medium speed is suitable for most routine techniques. Fast speed can deliver up to 50 mL in 5 seconds and can be used for rapid filling of large pipets or breaking up cell clumps. Slow speed is ideal when using small pipettes or when more precise delivery is required. A gravity drain model is available which substitutes a gravity drain (G) function for the fast (F) mode on the dispense button.

The XP is powered by a 9 volt (Ni-MH) rechargeable battery.

A Tissue Culture Nosepiece, which features a unique filter element, will cease to allow air to pass in either direction if it becomes wet, alerting the user to possible contamination of the rubber insert.

Features:

• The lightweight, compact Portable Pipet-Aid®
• Three-speed settings provide more precise control for use in the pipet filler mode and the pipette dispenser mode
• Easy access battery replacement
• EZ Grip nosepiece with double membrane filter
• Removable stand

Specifications

• Size: 5.5˝
• Weight: 7.5 oz.
• Capacity: Accepts 1 to 100 mL pipets
• Battery: 9 Volt Ni-MH

Specifications:

• Part# 3121000074
• Single-channel
• Fixed
• 100 µL
• Yellow

Specifications:

• Outside dimensions: 18 3/4" wide, 31" deep, & 27 5/8" high (476mm wide, 787mm deep, 702mm high)
• Chamber dimensions: 16" dia & 26" deep (406mm & 660mm)
• Trays: 2
• Tray capacity: 12" x 20" x 4" (305mm x 508mm x 102mm)
• Electrical requirements:
  • Unit is rated at 12KW at 236 volts & equipped for operation at:
  • 208-240 VAC, 3 wire, 1 Phase, 60 Hz
  • 208-240 VAC, 4 wire, 3 Phase, 60 Hz
  • 220 VAC, 1 Phase, 50 Hz
  • 220 VAC, 3 Phase, 50 Hz

Standard Equipment will include:

• Automatic temperature control
• Thermometer - 180 - 300 F (82-149 C)
• Safety Valve
• 0-30 lb. steam gauge
• 0-60 minute timer

Specifications:

• Outside dimensions: 18 3/4" wide, 31" deep, & 27 5/8" high (476mm wide, 787mm deep, 702mm high)
• Chamber dimensions: 16" dia & 26" deep (406mm & 660mm)
• Trays: 2 Tray capacity: 12" x 20" x 4" (305mm x 508mm x 102mm)
• Electrical requirements:
  • Unit is rated at 12KW at 236 volts & equipped for operation at:
  • 208-240 VAC, 3 wire, 1 Phase, 60 Hz
  • 208-240 VAC, 4 wire, 3 Phase, 60 Hz
  • 220 VAC, 1 Phase, 50 Hz
  • 220 VAC, 3 Phase, 50 Hz

Standard Equipment will include:

• Automatic temperature control
• Thermometer - 180 - 300 F (82-149 C)
• Safety Valve
• 0-30 lb. steam gauge
• 0-60 minute timer

For Preparative Scale Applications

Specifications:

• Trigger Modes: Time slices, Peak (threshold, up- /downslope), Timetable (combination of time intervals and peak) and Manual trigger (supported only with G1323BControl Module)
• Operating Modes: Discrete fractions: default mode for all vessels. The flow is diverted to waste, while moving from one vessel position to the next vessel position Continuous flow: optional, available only when using well plates. It is possible to move from one well plate position to the next one without diverting the flow into the well plate to waste
• Test tube /plate sizes: Minimum 48 mm to 100 mm maximum
• Maximum tube volume: ca. 45 ml
• Maximum flow rate: 100 ml / min (depending on viscosity and generated back pressure, max. 6 bar at the diverter valve)
• Delay volumes [μl]:
  • Fraction collector inlet to diverter valve: -500 (typical, depends on length of the tubing)
  • Diverter valve: ~15
  • Diverter valve to needle: ~110
  • Needle: -~5
• Delay calibration Sensor: Single wavelength absorbance detector working at 654 nm, consisting of a LED and a photo diode
• Diverter Valve: 3/2 Diverter valve with low internal volume (15 μl), switching time < 100 ms, maximum operating pressure 6 bar
• Cooling: Optional (with additional G1330B), performance depending on ambient conditions and the volume of collected fractions
• Maximum capacity: 3 fraction collectors in parallel plus one recovery fraction collector connected via 12-Position, 13-Port Selector valve
• GLP features Early maintenance feedback (EMF), electronic records of maintenance and errors
• Interfaces: Controller-area network (CAN). optional; LAN or external contacts interface RS232C, APG-remote (for remote start / stop signals to / from other modules) Interface to G1330A Thermostat CAN-DC-out for operation of Agilent approved external devices like valves
• Safety features: Leak detection and safe leak handling, error detection and display, exhaust fan for fume extraction of hazardous vapors

Can be sold as an individual component or as part of a complete stack

For Preparative Scale Applications

Specifications:

• Trigger Modes: Time slices, Peak (threshold, up- /downslope), Timetable (combination of time intervals and peak) and Manual trigger (supported only with G1323BControl Module)
• Operating Modes: Discrete fractions: default mode for all vessels. The flow is diverted to waste, while moving from one vessel position to the next vessel position Continuous flow: optional, available only when using well plates. It is possible to move from one well plate position to the next one without diverting the flow into the well plate to waste
• Test tube /plate sizes: Minimum 48 mm to 100 mm maximum
• Maximum tube volume: ca. 45 ml
• Maximum flow rate: 100 ml / min (depending on viscosity and generated back pressure, max. 6 bar at the diverter valve)
• Delay volumes [μl]:
  • Fraction collector inlet to diverter valve: -500 (typical, depends on length of the tubing)
  • Diverter valve: ~15
  • Diverter valve to needle: ~110
  • Needle: -~5
• Delay calibration Sensor: Single wavelength absorbance detector working at 654 nm, consisting of a LED and a photo diode
• Diverter Valve: 3/2 Diverter valve with low internal volume (15 μl), switching time < 100 ms, maximum operating pressure 6 bar
• Cooling: Optional (with additional G1330B), performance depending on ambient conditions and the volume of collected fractions
• Maximum capacity: 3 fraction collectors in parallel plus one recovery fraction collector connected via 12-Position, 13-Port Selector valve
• GLP features Early maintenance feedback (EMF), electronic records of maintenance and errors
• Interfaces: Controller-area network (CAN). optional; LAN or external contacts interface RS232C, APG-remote (for remote start / stop signals to / from other modules) Interface to G1330A Thermostat CAN-DC-out for operation of Agilent approved external devices like valves
• Safety features: Leak detection and safe leak handling, error detection and display, exhaust fan for fume extraction of hazardous vapors

Can be sold as an individual component or as part of a complete stack

For Preparative Scale Applications

Specifications:

• Trigger Modes: Time slices, Peak (threshold, up- /downslope), Timetable (combination of time intervals and peak) and Manual trigger (supported only with G1323BControl Module)
• Operating Modes: Discrete fractions: default mode for all vessels. The flow is diverted to waste, while moving from one vessel position to the next vessel position Continuous flow: optional, available only when using well plates. It is possible to move from one well plate position to the next one without diverting the flow into the well plate to waste
• Test tube /plate sizes: Minimum 48 mm to 100 mm maximum
• Maximum tube volume: ca. 45 ml
• Maximum flow rate: 100 ml / min (depending on viscosity and generated back pressure, max. 6 bar at the diverter valve)
• Delay volumes [μl]:
  • Fraction collector inlet to diverter valve: -500 (typical, depends on length of the tubing)
  • Diverter valve: ~15
  • Diverter valve to needle: ~110
  • Needle: -~5
• Delay calibration Sensor: Single wavelength absorbance detector working at 654 nm, consisting of a LED and a photo diode
• Diverter Valve: 3/2 Diverter valve with low internal volume (15 μl), switching time < 100 ms, maximum operating pressure 6 bar
• Cooling: Optional (with additional G1330B), performance depending on ambient conditions and the volume of collected fractions
• Maximum capacity: 3 fraction collectors in parallel plus one recovery fraction collector connected via 12-Position, 13-Port Selector valve
• GLP features Early maintenance feedback (EMF), electronic records of maintenance and errors
• Interfaces: Controller-area network (CAN). optional; LAN or external contacts interface RS232C, APG-remote (for remote start / stop signals to / from other modules) Interface to G1330A Thermostat CAN-DC-out for operation of Agilent approved external devices like valves
• Safety features: Leak detection and safe leak handling, error detection and display, exhaust fan for fume extraction of hazardous vapors

Can be sold as an individual component or as part of a complete stack

For Preparative Scale Applications

Specifications:

• Trigger Modes: Time slices, Peak (threshold, up- /downslope), Timetable (combination of time intervals and peak) and Manual trigger (supported only with G1323BControl Module)
• Operating Modes: Discrete fractions: default mode for all vessels. The flow is diverted to waste, while moving from one vessel position to the next vessel position Continuous flow: optional, available only when using well plates. It is possible to move from one well plate position to the next one without diverting the flow into the well plate to waste
• Test tube /plate sizes: Minimum 48 mm to 100 mm maximum
• Maximum tube volume: ca. 45 ml
• Maximum flow rate: 100 ml / min (depending on viscosity and generated back pressure, max. 6 bar at the diverter valve)
• Delay volumes [μl]:
  • Fraction collector inlet to diverter valve: -500 (typical, depends on length of the tubing)
  • Diverter valve: ~15
  • Diverter valve to needle: ~110
  • Needle: -~5
• Delay calibration Sensor: Single wavelength absorbance detector working at 654 nm, consisting of a LED and a photo diode
• Diverter Valve: 3/2 Diverter valve with low internal volume (15 μl), switching time < 100 ms, maximum operating pressure 6 bar
• Cooling: Optional (with additional G1330B), performance depending on ambient conditions and the volume of collected fractions
• Maximum capacity: 3 fraction collectors in parallel plus one recovery fraction collector connected via 12-Position, 13-Port Selector valve
• GLP features Early maintenance feedback (EMF), electronic records of maintenance and errors
• Interfaces: Controller-area network (CAN). optional; LAN or external contacts interface RS232C, APG-remote (for remote start / stop signals to / from other modules) Interface to G1330A Thermostat CAN-DC-out for operation of Agilent approved external devices like valves
• Safety features: Leak detection and safe leak handling, error detection and display, exhaust fan for fume extraction of hazardous vapors

Can be sold as an individual component or as part of a complete stack