Used Lab Equipment

Specification:

• Temperature Range: -73°C to +175°C
• Control Tolerance: ±0.2°C (Measured at the control sensor after stabilization)
• Uniformity: ±0.5°C (Variations throughout the chamber after stabilization)
• Heat-up Transition Time: 5°C/minute typical

• Refrigeration and Heating System

• High Stage Refrigerant: R-404A (Dupont HP-62)
• Low Stage Refrigerant: R-508B (Dupont SUVA-95)
• Compressors: 1/2 HP x 1/3 HP Copeland hermetic compressors in a cascade configuration.
• Condenser: Air cooled
• Heat of Rejection: 4,000 BTUH (maximum rated chamber load at maximum cooling rate from high temperature soak)
• Heater Power: 600 Watts
• Temperature Controller: 256 step, 40 profile, ramp and soak programmable memory. RS-232/485 interface.
• Limit Controller: Independent high and low temperature limits. Triggers an audible alarm and shuts down the chamber.
• Power Requirements: Input voltage - 120 V nominal (110 to 126 VAC), 60 Hz, 1 PH, maximum current draw 15 A, recommended minimum service 20 A
• Inside Dimensions (W x H x D): 16 x 12 x 14 in. (1.55 cubic feet) / 406 x 305 x 353 mm (44 liters)
• Outside Dimensions (W x H x D): 24 x 61 x 26 in. (610 x 1549 x 660 mm)
• Chamber Weight: 300 pounds

Specifications:

• Humidity Control
• Temperature Range: 0°C to 60°C
• Chamber Volume: 29 Cubic Feet / 821.2 Liters
• Temperature Uniforimity: ±0.3°C at 37°C
• Temperature Sensitiviy: ±0.1°C
• Chamber Dimensions (HxWxD):  60” x 31” x 27”
• Exterior Dimensions: (HxWxD):  88.5” x 38” x 32”
• Weight: 1040 LBS
• Capacity: 29 cu. ft. (821.2L)
• Voltage: 208/220V 60 Hz, 15.0A
• 4-wire power cord (including ground)
• NEMA 14-20P plug
• 6 solid stainless-steel shelves
• Exterior D x W x H: 32 x 38 x 88.5 in. (81.3 x 96.5 x 224.8cm)
• Interior D x W x H: 27 x 31 x 60 in. (68.6 x 78.7 x 152.4cm)

Broad Range of Features and Controls

• Wide temperature range of 0° to 60°C enhances the flexibility of the unit
• Relative humidity control via steam generator from above ambient to 95% at 37°C†
• Sophisticated digital controls
• Programmable ramp and soak cycles for temperature and RH†
• Durable cabinets feature true laminar airflow through side plenums for extremely tight uniformity
• Phenolic-coated evaporator for use in applications that create corrosive byproducts
• Manual control of defrost and refrigeration cycles
• Visible/audible safety alarms alert to over- and undertemperature conditions, deviation of humidity from set parameters (except Model 3920)

Durable Construction

• Cold-rolled steel, powder-coated cabinet
• 0 in. (5.1cm) thick, CFC-free, foamed-in-place polyurethane insulation
• Stainless-steel interior
• Solid stainless-steel adjustable shelves
• Directed horizontal airflow system for excellent uniformity
• Locking swivel casters ensure easy mobility during installation and cleaning
• Leveling feet provide stability and added safety in the lab

These accurate and reliable chambers are ideal for long-term high temperature and relative humidity (RH) testing. Designed to provide a wide range of environments, these units are suitable for both industrial and biotechnology specification testing, specifically continuous-duty projects.  All models are equipped with a gentle horizontal air flow system, which ensures stable, top-to-bottom temperature and RH uniformity. Low temperature models 9005L and 9010L feature CFC-free refrigerant. Relative humidity range may vary depending on temperature set point.  Digitally set, microprocessor temperature and humidity controllers allow precise setting with direct digital read-out in degrees and percentage RH.  The over-temperature safety control prevents possible damage to samples or equipment. A vapor generator compresses moisture and injects it into the chamber to provide controlled humidification. Automatic water level control maintains liquid level in humidity reservoir. Pressure coupling allows for easy hook-up of in-line plumbing or a carboy of distilled water. All units feature interior drain.

Specifications:

• Temp range: 40 to 70°C
• Capacity: 9 cu ft.
• Humidity range: 5% above ambient to 95% RH.
• Inside dimensions: 30"W x 20"D x 30"H.
• Interior: Stainless steel.
• Shelves: 2 shelves

Designed to culture dozens, and even hundreds, of samples on up to four independently controlled shakers. Powerful heater and fan provide rapid heat-up capability and temperature uniformity, and humidity control that minimizes evaporation.

Specifications:

• Speed: 25 to 400 RPM
• Temperature Range: 20°C below ambient to 60°C
• Temperature Gradient: ±0.5°C
• Humidity Control: 90% between 37°C and 45°C, 85% between 25°C and 36°C
• Dimensions: 55” x 30.5” x 78.5” in (W x D x H)
• Orbit Diameter: 1 or 2 in

Description:

The Thermo Forma Model 4535 Incubator Shaker is a large-capacity environmental shaker that allows for uniform heating and motion and accurate regulation of shaking speed. This equilibration creates faster operation and enhances the productivity of laboratories with shaking requirements. The Forma 4535 is designed to accommodate a wide variety of flasks, tubes, and other glassware. Program and store up to three user-defined combinations for ease of use and quick parameter recovery.

Specifications:

• Max Speed: 525 RPM
• Shaking Accuracy: ± 1 RPM
• Max Temperature: 60°C
• Temperature Control: ± 0.1°C
• Temperature Uniformity: ± 0.2°C
• Orbital Diameter: 1 inch
• Timer: 5 min to 199.99 hours / hold
• Dimensions (H x W x D): 40.5 x 26 x 45 in
• Power Requirements: 115 V, 60 Hz, 8.6 A

Rugged, high-performance baths maintain water temperature from ambient to 95°C or 99.9°C (depending on model) with ±0.2°C uniformity (at 37°C) and ±0.1°C control resolution (at 37°C) with stainless-steel gable cover.

Includes: Gable cover: stainless steel for all; Diffuser shelf

• Choice of analog or digital temperature control
• Chamber capacities ranging from 1.5 to 43L
• Front-mounted controls simplify operation
• Overtemperature safety circuitry prevents thermal runaway
• Dual-chamber models have independent controls for operating at different temperatures

Specifications

• Temperature Control Resolution: ±0.1°C†
• Temperature Uniformity: ±0.2°C†
• Temperature Range: Ambient to 99.9°C
• Chamber: Stainless steel
• Cabinet: Epoxy powder-coated stainless steel
• Capacity: 3.2 gal. (12L)3
• Reservoir: L x W x D: 11.5 x 12.5 x 6 in. (29.2 x 31.7 x 15.2cm)
• Weight: 40 lb. (18.1kg)
• Electrical Requirements: 120V 50/60Hz

The Decloaking Chamber is a programmable benchtop pressure cooker intended for laboratory use. It is programmed to allow the precise pressurized heating necessary for antigen retrieval and also has the capability to perform at a variety of temperatures ranging from 37 °C to 125 °C. The Decloaking Chamber is an excellent tool for heat-induced epitope-retrieval (HIER) methods. The proper use of heat and pressure in conjunction with the appropriate buffer solutions is of the utmost importance for consistent immunohistochemistry (IHC) staining. The Decloaking Chamber is designed to optimize and standardize antibody staining procedures and has been engineered to pass strict laboratory safety requirements. Temperature, pressure and pH can be monitored and recorded with the Decloaking Chamber to produce consistent staining, which will reduce repeat testing and false negatives.

Specification:

• Dimensions (W x D x H): 31 x 29 x 28
• Pan Capacity: 3.2 liters
• Weight: 3.7 (8.18 lbs)

The New Brunswick INNOVA 4000 Series are benchtop gyratory incubator shakers. Offering rigid control of temperature and agitation, the large-capacity INNOVA 4000 shaker is capable of culturing a wide array of organisms in test tubes and flasks up to 2.8 L.

The INNOVA series offers a wide temperature range. The INNOVA Model 4000 provides uniform temperature control in a range up to 60°C, while the high-temperature INNOVA 4080 incubator shaker increases the range to 80°C for added hybridization, adding capabilities for various molecular biology techniques, including hybridization studies, plasmid preps, DNA fingerprinting and more. The optional factory-installed cooling coil is also available for operating at sub-ambient conditions.

The INNOVA 4000 was designed with safety and ease of use in mind. The system includes an automatic cut-out feature of the shaker when the lid is opened to protect the operator. A fail-safe thermostat also turns off heat if temperature high limit is exceeded to protect cultures, and the hydraulic arm eases lid opening and closing.

Equipped with a large capacity blower and tightly constructed chamber, the INNOVA 4000 series incubator shaker has a self-correcting microprocessor feedback control which instantly compensates for changes in temperature. Another superior feature of the INNOVA 4000 include the interchangeable, large-capacity accessory platforms, 18" x 18" (46 x 46 cm) that accept gel trays, culture tubes and flasks to 2.8 L.

Specifications:

• Platform Size: 18 x 18
• Maximum Capacity (250 ml Flasks on Universal Platform): 18
• Capacity & Largest Flask Size on Universal Platform: 5 x 2L
• Orbit Diameter (in) 75
• Temperature Range (C°): Ambient +5 to 60 (4080 is Ambient +5 to 80)
• Digital Display: Yes
• Agitation: 25 to 500 rpm
• Type/Application: Benchtop
• Gassing Manifold: Optional
• Overall dimensions: W x D x H (in) 21 x 27.5 x 19.75
• Weight (lbs): 115

The New Brunswick INNOVA 4000 Series are benchtop gyratory incubator shakers. Offering rigid control of temperature and agitation, the large-capacity INNOVA 4000 shaker is capable of culturing a wide array of organisms in test tubes and flasks up to 2.8 L.

The INNOVA series offers a wide temperature range. The INNOVA Model 4000 provides uniform temperature control in a range up to 60°C, while the high-temperature INNOVA 4080 incubator shaker increases the range to 80°C for added hybridization, adding capabilities for various molecular biology techniques, including hybridization studies, plasmid preps, DNA fingerprinting and more. The optional factory-installed cooling coil is also available for operating at sub-ambient conditions.

The INNOVA 4000 was designed with safety and ease of use in mind. The system includes an automatic cut-out feature of the shaker when the lid is opened to protect the operator. A fail-safe thermostat also turns off heat if temperature high limit is exceeded to protect cultures, and the hydraulic arm eases lid opening and closing.

Equipped with a large capacity blower and tightly constructed chamber, the INNOVA 4000 series incubator shaker has a self-correcting microprocessor feedback control which instantly compensates for changes in temperature. Another superior feature of the INNOVA 4000 include the interchangeable, large-capacity accessory platforms, 18" x 18" (46 x 46 cm) that accept gel trays, culture tubes and flasks to 2.8 L.

Specifications:

• Platform Size: 18 x 18
• Maximum Capacity (250 ml Flasks on Universal Platform): 18
• Capacity & Largest Flask Size on Universal Platform: 5 x 2L
• Orbit Diameter (in)75
• Temperature Range (C°): Ambient +5 to 60 (4080 is Ambient +5 to 80)
• Digital Display: Yes
• Agitation: 25 to 500 rpm
• Type/Application: Benchtop
• Gassing Manifold: Optional
• Overall dimensions: W x D x H (in) 21 x 27.5 x 19.75
• Weight (lbs): 115

Description:

Boekel Scientific offers a wide variety of Dry Bath Incubators designed to accommodate an assortment of interchangeable Heating Block Modules. These reliable and economical products are ideal for a variety of applications including restriction digests, C.O.D. denaturing DNA, BUN, melting agar, coagulation studies, in situ hybridization and Hot Start PCR.

Specification:

• Temperature Range: +5ºC to 120ºC
• Stability: ±0.2°C @ 37°C

The Fisher Scientific Dry Bath Incubators offer exceptional temperature control and uniformity in addition to a powder coated steel body to provide durability for demanding applications.

Specifications:

• Temperature Range: 5 - 130 °C
• Temperature Stability: +/-1.5 °C
• Temperature Uniformity: +/-0.5 °C
• Power Requirements: 120V, 50/60Hz

Compact, flexible high precision tube and plate heating system with heated lid. System consists of a heating base with a variety of interchangeable, removable blocks for widely used tubes and plates. A waterbath insert (625 ml) is also available for heating buffers for washing microarrays or other applications.

Specifications:

• Dimensions: 12 x 6 x 10 in
• Weight: 6 lbs
• Temperature Range: Ambient +5 to 99C
• Temperature Regulation: +/- 0.1C

Provides uniform heat distribution and reduces air movement helping to prevent cross contamination of samples. Ideal for applications where forced air cannot be tolerated.

Specifications:

• Temperature range: 5℃ above ambient to 65℃
• Dimensions: D x H x W (15 x 21.0 x 15.7in)
• Chamber size: 1.3 cu. ft. (37 L)

These multi-functional shakers provide a 3-dimensional "nutating" motion for thorough, foam-free mixing in blood and centrifuge tubes, as well as in a variety of flat vessels.Both models come standard with autoclavable dimpled mats while optional flat mats are also available for mixing other vessel types. Stacking platforms can be purchased as accessories, effectively doubling the usable surface area of each model. Even the smallest single platform configuration has 24% more platform work surface than traditional nutating mixers. These mixers feature maintenance free, brushless motors capable of loads up to 2kg and are safe for use in cold rooms and incubators.

Specification:

• Speed: Fixed, 24 rpm (20 rpm, 230V)
• Tilt Angle: +/-20°
• Platform Size: 10.5 x 7.5 in./ 27 x 19 cm
• Load Capacity: 4 lbs. / 2 kg
• Operating Temp. Range: +4 to +45°C
• Dimensions: (W x D x H): 10.5 x 7.5 x 8 in. / 27 x 19 x 20 cm
• Weight: 4.4 lbs. / 2.2 kg
• Electrical: 115V or 230V, 50-60Hz, 50W

Features:

Isotemp refrigerated, 27.3 cu ft, w/chart recorder

Specifications:

• Volts: 115
• Phase: 1
• Hz.: 60