Used Lab Equipment

Features:

• G1364A Thermostatted Fraction Collector, preparative scale, can be created by additionally ordering and installing a G1330A Fraction Collector Thermostat

• For preparative scale applications

Specifications:

• Trigger Modes: Time slices, Peak (threshold, up- /downslope), Timetable (combination of time intervals and peak) and Manual trigger (supported only with G1323BControl Module)
• Operating Modes: Discrete fractions: default mode for all vessels. The flow is diverted to waste, while moving from one vessel position to the next vessel position Continuous flow: optional, available only when using well plates. It is possible to move from one well plate position to the next one without diverting the flow into the well plate to waste
• Test tube /plate sizes: Minimum 48 mm to 100 mm maximum
• Maximum tube volume: ca. 45 ml
• Maximum flow rate: 100 ml / min (depending on viscosity and generated back pressure, max. 6 bar at the diverter valve)
• Delay volumes [μl]:
• Fraction collector inlet to diverter valve: -500 (typical, depends on length of the tubing)
• Diverter valve: ~15
• Diverter valve to needle: ~110
• Needle: -~5
• Delay calibration Sensor: Single wavelength absorbance detector working at 654 nm, consisting of a LED and a photo diode
• Diverter Valve: 3/2 Diverter valve with low internal volume (15 μl), switching time < 100 ms, maximum operating pressure 6 bar
• Cooling: Optional (with additional G1330B), performance depending on ambient conditions and the volume of collected fractions
• Maximum capacity: 3 fraction collectors in parallel plus one recovery fraction collector connected via 12-Position, 13-Port Selector valve
• GLP features Early maintenance feedback (EMF), electronic records of maintenance and errors
• Interfaces: Controller-area network (CAN). optional; LAN or external contacts interface RS232C, APG-remote (for remote start / stop signals to / from other modules) Interface to G1330A Thermostat CAN-DC-out for operation of Agilent approved external devices like valves
• Safety features: Leak detection and safe leak handling, error detection and display, exhaust fan for fume extraction of hazardous vapors

Can be sold as an individual component or as part of a complete stack

Features:

• G1364B Fraction Collector, preparative scale, designed for flow rates up to 100 ml / min. and for the use with vials, deep well plates and test tubes up to 100 mm height
• For Preparative Scale Applications

Specifications:

• Trigger Modes: Time slices, Peak (threshold, up- /downslope), Timetable (combination of time intervals and peak) and Manual trigger (supported only with G1323BControl Module)
• Operating Modes: Discrete fractions: default mode for all vessels. The flow is diverted to waste, while moving from one vessel position to the next vessel position Continuous flow: optional, available only when using well plates. It is possible to move from one well plate position to the next one without diverting the flow into the well plate to waste
• Test tube /plate sizes: Minimum 48 mm to 100 mm maximum
• Maximum tube volume: ca. 45 ml
• Maximum flow rate: 100 ml / min (depending on viscosity and generated back pressure, max. 6 bar at the diverter valve)
• Delay volumes [μl]:
• Fraction collector inlet to diverter valve: -500 (typical, depends on length of the tubing)
• Diverter valve: ~15
• Diverter valve to needle: ~110
• Needle: -~5
• Delay calibration Sensor: Single wavelength absorbance detector working at 654 nm, consisting of a LED and a photo diode
• Diverter Valve: 3/2 Diverter valve with low internal volume (15 μl), switching time < 100 ms, maximum operating pressure 6 bar
• Cooling: Optional (with additional G1330B), performance depending on ambient conditions and the volume of collected fractions
• Maximum capacity: 3 fraction collectors in parallel plus one recovery fraction collector connected via 12-Position, 13-Port Selector valve
• GLP features Early maintenance feedback (EMF), electronic records of maintenance and errors
• Interfaces: Controller-area network (CAN). optional; LAN or external contacts interface RS232C, APG-remote (for remote start / stop signals to / from other modules) Interface to G1330A Thermostat CAN-DC-out for operation of Agilent approved external devices like valves
• Safety features: Leak detection and safe leak handling, error detection and display, exhaust fan for fume extraction of hazardous vapors

Can be sold as an individual component or as part of a complete stack

Features:

• G1364C Fraction Collector, analytical scale, designed for flow rates below 10 ml / min. (can be modified for higher flow rates) and for the use with vials, test tubes of up to 75 mm height, well-plates and a 40-funnel tray connecting to external locations of any size 

• For analytical scale applications

Specifications:

• Trigger Modes: Time slices, Peak (threshold, up- /downslope), Timetable (combination of time intervals and peak) and Manual trigger (supported only with G1323BControl Module)
• Operating Modes: Discrete fractions: default mode for all vessels. The flow is diverted to waste, while moving from one vessel position to the next vessel position Continuous flow: optional, available only when using well plates. It is possible to move from one well plate position to the next one without diverting the flow into the well plate to waste
• Test tube /plate sizes: Minimum 48 mm to 100 mm maximum
• Maximum tube volume: ca. 45 ml
• Maximum flow rate: 100 ml / min (depending on viscosity and generated back pressure, max. 6 bar at the diverter valve)
• Delay volumes [μl]:
• Fraction collector inlet to diverter valve: -500 (typical, depends on length of the tubing)
• Diverter valve: ~15
• Diverter valve to needle: ~110
• Needle: -~5
• Delay calibration Sensor: Single wavelength absorbance detector working at 654 nm, consisting of a LED and a photo diode
• Diverter Valve: 3/2 Diverter valve with low internal volume (15 μl), switching time < 100 ms, maximum operating pressure 6 bar
• Cooling: Optional (with additional G1330B), performance depending on ambient conditions and the volume of collected fractions
• Maximum capacity: 3 fraction collectors in parallel plus one recovery fraction collector connected via 12-Position, 13-Port Selector valve
• GLP features Early maintenance feedback (EMF), electronic records of maintenance and errors
• Interfaces: Controller-area network (CAN). optional; LAN or external contacts interface RS232C, APG-remote (for remote start / stop signals to / from other modules) Interface to G1330A Thermostat CAN-DC-out for operation of Agilent approved external devices like valves
• Safety features: Leak detection and safe leak handling, error detection and display, exhaust fan for fume extraction of hazardous vapors

Can be sold as an individual component or as part of a complete stack

For Preparative Scale Applications

Specifications:

• Trigger Modes: Time slices, Peak (threshold, up- /downslope), Timetable (combination of time intervals and peak) and Manual trigger (supported only with G1323BControl Module)
• Operating Modes: Discrete fractions: default mode for all vessels. The flow is diverted to waste, while moving from one vessel position to the next vessel position Continuous flow: optional, available only when using well plates. It is possible to move from one well plate position to the next one without diverting the flow into the well plate to waste
• Test tube /plate sizes: Minimum 48 mm to 100 mm maximum
• Maximum tube volume: ca. 45 ml
• Maximum flow rate: 100 ml / min (depending on viscosity and generated back pressure, max. 6 bar at the diverter valve)
• Delay volumes [μl]:
  • Fraction collector inlet to diverter valve: -500 (typical, depends on length of the tubing)
  • Diverter valve: ~15
  • Diverter valve to needle: ~110
  • Needle: -~5
• Delay calibration Sensor: Single wavelength absorbance detector working at 654 nm, consisting of a LED and a photo diode
• Diverter Valve: 3/2 Diverter valve with low internal volume (15 μl), switching time < 100 ms, maximum operating pressure 6 bar
• Cooling: Optional (with additional G1330B), performance depending on ambient conditions and the volume of collected fractions
• Maximum capacity: 3 fraction collectors in parallel plus one recovery fraction collector connected via 12-Position, 13-Port Selector valve
• GLP features Early maintenance feedback (EMF), electronic records of maintenance and errors
• Interfaces: Controller-area network (CAN). optional; LAN or external contacts interface RS232C, APG-remote (for remote start / stop signals to / from other modules) Interface to G1330A Thermostat CAN-DC-out for operation of Agilent approved external devices like valves
• Safety features: Leak detection and safe leak handling, error detection and display, exhaust fan for fume extraction of hazardous vapors

Can be sold as an individual component or as part of a complete stack

Specification:

• 3-way valve: Three-port, PTFE, 67 µL internal volume. 3,5 µL dead volume from the common port to the normally closed port, up to 20 mL/min with large bore needle OR Three-port, PTFE, 114 µL internal volume. 6 µL dead volume from the common port to the normally closed port, up to 200 mL/min with large bore needle.

• Contact control

• Contact closure inputs for start/advance and end/home
• Event mark output
• One programmable output for control of peripheral devices
• Data acquisition: An input channel for analog-to-digital conversion; digital data is transmitted on the GSIOC
• Detector input: ±100 mV full scale
• Display: two lines of 24 alphanumeric characters; backlit LCD
• Drop counting: Up to 9999 drops per fraction. Maximum rate: 20 drops per second

• Environmental conditions

• Indoor use only
• Up to 2000 meters altitude
• 5° - 40°C temperature range
• 75 - 105 kPa air pressure
• Pollution degree 1 or 2 in accordance with IEC 66
• Maximum relative humidity 80% for temperatures up to 31°, decreasing linearly to 50% relative humidity at 40°C.
• Event marker: 100 ms pulse (contact closure)
• Maximum collection volume/tube: 32 mL (18 x 180 mm tube) or 25 mL (18 x 150 mm tube)
• Maximum fractions: up to 768 fractions when configured with eight 96-well, 2 mL Whatman/Plyfiltronics microplates on a Code 17 rack
• Multi-cycle operation: repetitive collection of each sample into same set of tubes or collection each sample into different set of tubes
• Multiple column collection: simultaneous collection from up to 18 columns with installation of optimal multiple column adapter(s).
• Number of racks: One Code 16 or 16D rack, one Code 17 rack, or up to four Code 20-Series racks (all racks must be same code)
• Operating modes: Time, drop, peak + time, peak + drop, and manual

• Peak detection

• Adaptive slope algorithm that applies use-specified parameters to accommodate drifting baselines, negative peaks, and asymmetrical peaks or absolute threshold level that collects all peaks above specified millivolt value
• Peak Parameters: peak height or level, in mV, and peak width at half-height, in minutes
• Minimum peak height for fractionation: 0.1 mV full scale
• Detector-collector delay: 0.01 minute increments
• Physical space requirement: 47.9 x 46.4 x 33.0 cm (18.9 x 18.3 x 13.0 in.)

• Power requirements

• Frequency: 50 to 60 Hz
• Voltage: 100 - 120V or 220 - 240V, mains voltage fluctuations not to exceed ±10% of the nominal voltage
• Current rating: 0.5A for 100 - 120V or 0.25A for 220 - 240V
• Programmable time units (min.): from 0.01 to 99.99 minutes per tube, with 0.01 minute limit of resolution
• Software control: Via Gilson Serial Input/Output CHannel (GSIOC) or by contact closure
• Time based programming: Up to ten collection windows and ten drain steps in any mode
• Tube change time: 100-720ms. Center-to-center, depending on rack type
• Weight: 10.9 kg (24 lbs)

Description:

The Transgenomic WAVE Fragment Collector Model FCW 200 enables fully automated purification of nucleic acids with the WAVE System. Nucleic acid samples collected by the FCW 200 meet high purity and sample concentration requirements for use in molecular genetic analyses and genomics. The dual plate FCW 200 enables fully automated fractionation and purification of ss- and dsDNA, RNA, and synthetic oligonucleotides with minimum sample loss and minimum cross contamination. The FCW 200 is controlled by both NAVIGATOR Software and WAVEMAKER Software enabling multiple modes for collection of nucleic acid fragments including: Minimum detection threshold above baseline with proprietary baseline drift compensation; Time/eluent volume window around peak retention time; Combined peak and threshold detection; Positive and/or negative slope detection; Combined slope and threshold detection; User-defined collection time windows.

Specifications:

• Electrical: 85-264 V, 47-440 Hz, 300 W
• Dimensions: 14” x 18” x 13”

A proprietary band function enables obtaining accurate fractions even when the peak elution time varies, by catching the target component according to variations in the chromatogram. If connected to workstation software, fractions can be simulated on screen to determine whether or not the fraction program is appropriate.

Details:

• Small and Large Volume Collection Capacity
• The FRC-10A collects both analytical and preparative fractions. The standard configuration has a 144 5mL vial capacity. The large volume kit can be added for large volume collection.
• Precise Peltier Temperature Control
• For automated collection of thermally-labile fractions, Peltier temperature control keeps temperatures stable within a 4-70º C range.
• Simplified Graphical Parameter Entry
• Set up fractionation parameters graphically from the SCL-10AVP System Controller. Eliminate the guesswork of determining slope and level values.
• Fraction Collection Flexibility
• Tailor the collection to your application requirements.  Choose from collection criteria such as volume, threshold, and peak purity. A precise peak division feature ensures high purity fractions. The FRC-10A automatically adjusts for retention time shifts, so that only the peak of interest is collected. Our slope-override capability enables continued collection, even when the detector signal is off-scale.

Specifications:

• Drive System and Fraction Collection Methods: Arm-Movement X-Y System
• Select either solenoid valve or direct through nozzle
• Fraction Modes: Manual or programmed fraction collection by combining 14 types of parameters, such as slope, level, and band
• Number of Fractions: 16 to 144
• Collection Tubes: Glass: 3.5, 5, 20, 32, or 50 mL, or user supplied
• Polypropylene: 4.5, 5, 25, or 50 mL, or user supplied

FRAC-100 (with its drop counting accessory) can collect fractions in a variety of different ways, based either on time, volume or drop counting, controlled via simple programs specified by the operator. For example, you can choose to collect uniform fractions of a fixed time period.

Specifications:

• Fraction Size Timing:01-99.99 min (0.01 min increments)
• Fraction Size Timing: 100-999.9 min (0.1 min increments)
• Fraction Size Timing: 1000-9 999 min (1 min increments) within an accuracy of ± 0.02%
• Fraction Size Volume: 01-99.99 ml (0.01 ml increments)
• Fraction Size Volume: 100-999.9 ml (0.1 ml increments)
• Fraction Size Volume: 1000-9 999 ml (1 ml increments) within and accuracy of ± 0.02%
• Maximum Drop Rate: 15 drops/sec
• Weight: 5 kg
• Dimensions: 30 x 29 x 39 cm
• Environment: +4 to +40°C, 20-95% relative humidity
• Environment: 84-106 kPa (840-1060 mbar) atmospheric pressure
• Peak Memory: up to 11 peaks
• Tubing:7 – 2 mm outer diameter

Features:

• Frac-900 designed to work with AKTA series FPLC
• 95 places rack for 10-18mm tubes
• Fraction size 0.05 - 100 ml (0.001 ml increments)
• Time mode 0.01-9.999min, volume mode 0.01-9.999 ml
• Max flow rate 100 ml/min
• Peak detection and location capability, programmable collection modes

Features:

• Frac-900 designed to work with AKTA series FPLC
• 95 places rack for 10-18mm tubes
• Fraction size 0.05 - 100 ml (0.001 ml increments)
• Time mode 0.01-9.999min, volume mode 0.01-9.999 ml
• Max flow rate 100 ml/min
• Peak detection and location capability, programmable collection modes

Includes:

• Manual
• Vial Holder rack
• Power Cord

Specifications:

• Maximum flow rate: 100 ml/min
• pH stability range: 1 to 13, 1 to 14 (<1 day exposure)

Fraction size

• Volume mode: to 99999.99 ml
• Time mode: to 99999.99 min

No spillage range for DropSync

• Microplates: 0 to 1.0 ml/min
• 12 mm rack: 0 to 1.5 ml/min
• 18 and 30 mm rack: 0 to 2.0 ml/min

No spillage range for Accumulator

• All racks: 0 to 100 ml/min

Optional Installation, Familiarization, and Extended Warranty available

Includes:

• G1322 Degasser
• G1311 Quarternary Pump or G1312A Binary Pump($1000 Less)
• G1313A Autosampler
• G1316A Column Compartment
• G1315A Diode Array Detector
• Computer Loaded with ChemStation
• Monitor – Mouse – Keyboard
• Cables and Manuals

The components can be customized to your needs.

Please let me know if I can be of any additional assistance.

Includes: 

• Qty (2) - G1361A Agilent 1100 Series Prep Pumps
• G1315A DAD Diode Array Detector (G1314A VWD Detector also available)
• G2258A Agilent 1100 Prep Autosampler
• G1364B AFC Automated Fraction Collector
• Computer Loaded with ChemStation
• Monitor – Mouse – Keyboard
• Cables and Manuals

Includes:
• G1311 Quarternary Pump or G1312A Binary Pump($1000 Less)
• G1329B Autosampler
• G1316A Column Compartment
• G4212B Dioade Array Detector
• Computer Loaded with OpenLab Software 
• Monitor – Mouse – Keyboard
• Cables and Manuals

The components can be customized to your needs.

Includes:

• Qty (2) - G1361A Agilent 1100 Series Prep Pumps
• G1315A DAD Diode Array Detector (G1314A VWD Detector also available)
• G2258A Agilent 1100 Prep Dual Loop Autosampler (Manual Injector also an option)
• G1364B AFC Automated Fraction Collector
• Computer Loaded with ChemStation
• Monitor – Mouse – Keyboard
• Cables and Manuals

G1361 Prep Pump

Features:

• Extended flow rate range
• Without changing pump heads, provides flow rates up to 100 mL/min at 400 bar
• For preparative and analytical applications with low flow rates (0.5 mL/min, upward), provides precise high-pressure binary gradient formation with low delay volume (700 uL)
• Automated seal wash using a peristaltic pump extends seal lifetime
• Pumps stop in response to column blockage or leaks
• Automated electromagnetic purge valve simplifies system setup
• Software provides solvent level control that keeps the pump from running dry