Used Lab Equipment

Specifications:

• GLP features: Early maintenance feedback (EMF), electronic records of maintenance and errors
• Communications Controller: area network (CAN). RS232C, APG-remote standard, optional four external contact closures and BCD vial number output
• Safety features:  Leak detection and safe leak handling, low voltages in maintenance areas, error detection and display
• Injection range:  
  • 1 – 100 μl in 0.1 μl increments
  • Up to 1500 μl with multiple draw (hardware modification required)
• Precision:
  • Typically < 0.5 % RSD of peak areas from 5 – 100 μl,
  • Typically < 1 % RSD from 1 – 5 μl
• Sample viscosity range:  0.2 – 5 cp
• Sample capacity:
  • 2 × well-plates (MTP) + 10 × 2 ml vials
  • 100x2ml in one tray
  • 40 x 2 ml in half tray
• Injection cycle time:
  • Typically < 30 s using following standard conditions:
  • Default draw speed: 200 μl/min
  • Default eject speed: 200 μl/min
  • Injection volume: 5 μl
• Carry-over Typically:
  • < 0.01 % using the following conditions:
  • Column: 125 x 4 mm Hypersil ODS, 5 μm
  • Mobile phase: Water/Acetonitrile = 80/20
  • Flow rate: 1 ml/min
  • Injection volume: 1 μl caffeine (1 mg/ml), 5 μl water to test carryover
  • Outside wash of needle before injection: 20 sec with water using flush port

Specifications:

• GLP features: Early maintenance feedback (EMF), electronic records of maintenance and errors
• Communications: Communications Controller-area network (CAN). RS232C, APG-remote standard, optional four external contact closures and BCD vial number output
• Safety features: Leak detection and safe leak handling, low voltages in maintenance areas, error detection and display
• Injection range:
  
  • – 8 µl in 0.01 µl increments with the small loop capillary
  • – 40 µl in 0.01 µl increments with the extended loop capillary
• Precision:
  • Typically < 0.5 % RSD of peak areas from 5 – 40 µl,
  • Typically < 1 % RSD from 1 – 5 µl
  • Typically < 3 % RSD from 0.2 – 1 µl
• Sample viscosity range: 2 – 5 cp
• Sample capacity:
  • 2× well-plates (MTP) + 10 × 2 ml vials
  • 100 x 2 ml in one tray
  • 40 x 2 ml in half tray
• Injection cycle time:
  • Typically, < 30 s using following standard conditions:
  • Default draw speed: 4 µl/min
  • Default eject speed: 10 µl/min
  • Injection volume: 0.1 µl
• Carry-over:
  • Typically < 0.05 % using the following conditions:
  • Column: 150 x 0.5 mm Hypersil ODS, 3 µm
  • Mobile phase: Water/Acetonitrile = 85/15
  • Column Flow rate: 13 µl/min
  • Injection volume: 1 µl caffeine (=25ng caffeine), 1 µl water to test carryover
  • Outside wash of needle before injection: 20 sec with water using flush port

The Agilent 1200 Series autosampler is designed for use with other modules of the Agilent 1200 Series LC system or with other LC systems if adequate remote control inputs and outputs are available. The autosampler is controlled from the Agilent 1200 Series control module or from the Agilent ChemStation

for LC systems.

Specifications:

• Weight: 15.5 kg (34.2 lbs)
• Dimensions (height × width × depth): 200 × 345 × 440 mm (8 × 13.5 × 17 inches)
• Line voltage: 100 – 240 VAC, ±10 % Wide-ranging capability
• Line frequency: 50 or 60 Hz, ±5 %
• Power consumption (apparent power): 300 VA Maximum
• Power consumption (active power): 200 W Maximum
• Ambient operating temperature: 4 to 55 8C (41 to 131 8F)
• Ambient non-operating temperature: -40 to 70 8C (-4 to 158 8F)
• Humidity: < 95 %, at 25 to 40 8C (77 to 104 8F) Non-condensing
• Operating Altitude: Up to 2000 m (6500 ft)
• Non-operating altitude: Up to 4600 m (14950 ft) For storing the autosampler

The Leap technologies CTC PAL HTC Auto sampler for HPLCs offer Precise and Accurate sample Loading, high throughput, flexible analysis while taking up limited bench space.

Includes:

• HTC PAL Autosampler (Width: 534mm Depth: 385mm Height: 648mm)
• Temperature controlled sample storage 3 drawer
• XYZ injector/Arm
• LC Injection valve- 6 port
• Wash station
• Gameboy controller
• Power Supply
• Manual

Specifications:

• Unit Power Supply: (Input) 100-240VAC, 50-60Hz, 4A, (Output) 36VDC, 4.16A
• Cooler Power Supply: (Input) 100-240VAC, 50-60Hz, 2A, (Output) 24VDC, 4.5A
• Cooling stack
• Waste Station
• Valve
• Hand Held Controller

Features:

• Optimized for high-throughput applications and sub two micron column particles
• Maximum reproducibility with isothermal injection and separation
• Greater application flexibility with multiple sample formats
• Superior robustness with a diamond coated high pressure valve Accela Photo Diode Array Detector
• Highest detection sensitivity with proprietary LightPipe technology
• Designed for U-HPLC separations with a 1cm path length, 2µL LightPipe flowcell
• Maximum peak resolution with fiberoptic beam shaper
• Easy maintenance with integrated wavelength validation

Specifications:

• Sample capacity:
  • 200 vials in five removable trays
  • 288 samples in three 96-well microplates
  • 1152 samples in three 384-well microplates
• Standard vial:8 mL volume
• Injection precision: < 1.0% RSD at 5 μL and up
• Partial loop injection volume:
  • 10 μL with standard 25 μL sample loop and 250 μL syringe
  • Up to 1000 μL injection volume with optional loops and syringes
• Fixed loop (full loop) injection volume:
  • 25 μL with standard loop and 250 μL syringe
  • Up to 1000 μL injection volume with optional loops and syringes
• Sample carryover:
  • < 0.1%
  • 6 mL flush volumes, user-specified for internal and external needle wash cycles
• Minimum sample volume: 1 μL can be injected from 5 μL
• Needle height control:
  • Programmable in 0.1 mm increments
  • Active vial bottom search selectable on/off
• Column oven: Programmable in 1 °C increments from 5 to 95 °C
• Tray temperature control:
  • Programmable in 1 °C increments from 0 to 60 °C
  • Typical vial temperature from 4 to 50 °C
• Reagent vials: Four 16 mL vials can be specified for flush/wash or dilution functions
• Remote inputs: Pump ready, inject hold
• Remote outputs: Pump stop, autosampler ready, inject, gradient start, four timed events
• Ambient environment:10 to 40 °C, 5 to 95% relative humidity, non-condensing
• Power requirements: 100/120/220/240 Vac nominal; 50/60 Hz, 550 VA

Specifications:

• Capacity: 2 sets of 30 x 0.5 mL tubes

• Temperature Range: 0 - 105°C

• Temperature Accuracy: +/- 0.3°C

• Temperature Uniformity: +/- 0.4°C

• Ramping Speed: up to 3°C/sec

• Dimensions: 12 x 12 x 12 in

• Weight: 25 lbs

• Power Requirements: 100 - 240V, 50/60Hz, 850W

• Lowest Programmable Temperature: 30°C

Features:

Denley Wellwash 4 MK2 Microplate Washer 12 way head

Specifications:

• Injection range: From 0.1 – 100 µl in 0.1 µl increments
• Replicate injections: From 1 – 99 from one vial
• Injection cycle time: Typically 50 s, depending on draw speed and volume
• Sample capacity: 100 × 2 ml vials in tray

Specifications:

• Autosampler (Chiller Compatible)
• GLP features: Early maintenance feedback (EMF), electronic records of maintenance and errors
• Communications: Controller-area network (CAN). GPIB (IEEE-448), RS232C, APG-remote standard, optional four external contact closures and BCD vial number output
• Safety features: Leak detection and safe leak handling, low voltages in maintenance areas, error detection and display
• Injection range: 1– 100 µl in 0.1 µl increments Up to 1500 µl with multiple draw (hardware modification required)
• Replicate injections: 1– 99 from one vial
• Precision:
  • Typically < 0.5 % RSD of peak areas from 5 – 100 µl
  • Typically < 1 % RSD of peak areas from 1 – 5 µl
• Minimum sample volume: 1 µl from 5 µl sample in 100 µl microvial, or 1 µl from 10 µl sample in 300 µl microvial
• Carryover: Typically < 0.1 %, < 0.05 % with external needle cleaning
• Sample viscosity range: 2 – 50 cp
• Replicate injections per vial: 1 – 99
• Sample capacity:
  • 100 × 2-ml vials in 1 tray
  • 40 × 2-ml vials in ½ tray
  • 15 × 6-ml vials in ½ tray (Agilent vials only)
• Injection cycle time: Typically 50 s depending on draw speed and injection volume

Can be sold as an individual component or as part of a complete stack

Specifications:

• Autosampler Thermostat
• Operating temp range: 4 to 40°C (39 to 104°F)
• Operating humidity range: < 95%, non-condensing
• Maximum Power Consumption [VA]: 260 VA
• Maximum Power Consumption [W]: 210 W
• BTU: 717

Can be sold as an individual component or as part of a complete stack

Specifications:

• Autosampler Thermostat
• Operating temp range: 4 to 40°C (39 to 104°F)
• Operating humidity range: < 95%, non-condensing
• Maximum Power Consumption [VA]: 260 VA
• Maximum Power Consumption [W]: 210 W
• BTU: 717

Can be sold as an individual component or as part of a complete stack

Specifications:

• Sample capacity: 100 x 2 ml vials in 1 tray. Microvials (100 or 300 µl) with sleeves (reduced cooling performance with microvials)
• Settable injection volume
  • to 8 µl with small loop capillary
  • to 40 µl with extended loop capillary
• Precision
  • Typically < 0.5 % RSD from 5 to 40 µl
  • Typically < 1 % RSD from 1 to 5 µl
  • Typically < 3 % RSD from 0.2 to 1 µl
• Minimum sample volume: µl from 5 µl sample in 100 µl microvial, or 1 µl from 10 µl sample in 300 µl microvials
• Carryover
  • Typically < 0.1 % without automated needle wash
  • Typically < 0.05 % with external needle cleaning and 1 µl injection volume
• Sample viscosity range: 2 - 5 cp
• Recommended pH-range: - 8.5 solvent with pH < 2.3 should not contain acids which attack stainless steel. Upper pH range is limited by fused silica capillaries
• Material in contact with solvent: Stainless steel, sapphire, PTFE, PEEK, fused silica
• GLP features: Early maintenance feedback (EMF), electronic records of maintenance and errors
• Communications: Controller-area network (CAN). GPIB (IEEE-448), RS232C, APG-remote standard, optional four external contact closures and BCD vial number output
• Safety features: Leak detection and safe leak handling, low voltages in aintenance areas, error detection and display
• Housing: All material recyclable

Can be sold as an individual component or as part of a complete stack

Specifications:

• Pressure: Operating range 0 – 40 MPa (0 – 400 bar, 0 – 5800psi)
• GLP features: Early maintenance feedback (EMF), electronic records of maintenance and errors
• Communications: Controller-area network (CAN). GPIB (IEEE-448), RS232C, APG-remote standard, optional four external contact closures and BCD vial number output
• Safety features: Leak detection and safe leak handling, low voltages in maintenance areas, error detection and display
• Injection range:
  • 900 µl in 0.1 µl increments (recommended 1 µl increments)
  • Up to 1800 µl with multiple draw (hardware modification required)
  • Up to 5000 µl with multiple draw (hardware modification required)
• Replicate injections: – 99 from one vial
• Precision:
  • Typically < 0.5% RSD of peak areas from 5 – 2000 µl,
  • Typically < 1% RSD of peak areas from 2000 – 5000 µl
  • Typically < 3% RSD of peak areas from 1 – 5 µl
• Minimum sample volume:
  • µl from 5 µl sample in 100 µl microvial
  • 1 µl from 10 µl sample in 300 µl microvial
• Sample viscosity range: 0.2 – 50 cp
• Sample capacity:
  • 100 × 2-ml vials in 1 tray
  • 15 × 6-ml vials in ½ tray (Agilent vials only)
• Injection cycle time: Typically 50 s, depending on draw speed and injection volume

The Agilent 1200 ALS Thermostat, G1330A controls temperature for either HPLCs or fraction collectors. The ALS thermostat contains Peltier-controlled heat exchangers. A fan draws air from the area above the sample vial tray of the autosampler and is then blown through the fins of the cooling/heating module. There it is cooled or heated according to the temperature setting.

Specifications:

• Weight: 20.7 kg (45.6 lbs)
• Dimensions: 140 × 345 × 435 mm (5.5 × 13.5 × 17 inches)
• Line Voltage: 100 – 120 or 220 – 240 VAC, ± 10 % Automatic selection
• Line Frequency: 50 or 60 Hz, ± 5 %
• Power consumption Autosampler: 300 VA 
• ALS Thermostat: 260 VA