Used Lab Equipment

Description:

Peristaltic pumps are the simplest pump, with no valves, seals or glands to clog or corrode. The fluid contacts only the bore of a tube, eliminating the risk of the pump contaminating the fluid, or the fluid contaminating the pump. Peristaltic pumps can run dry. Peristaltic pumping is ideal for most fluids, including viscous, shear-sensitive, corrosive and abrasive fluids, and those containing suspended solids. They are especially useful for pumping operations where hygiene is important. Peristaltic pumps operate on the positive displacement principle. They are particularly suitable for metering, dosing and dispensing applications. Pumps are easy to install, simple to operate and inexpensive to maintain.

Specifications:

• Supply voltage/frequency: 100-120V/200-240V 50/60Hz 1ph
• Maximum voltage fluctuation: ±10% of nominal voltage. A well regulated electrical mains supply is required along with cable connections conforming to the best practice of noise immunity
• Power consumption: 100VA
• Full load current: <0.43A at 230V; <0.86A at 115V
• Operating temperature range: 4°C to 40°C, 40°F to 104°F
• Storage temperature range: -40°C to 70°C, -40°F to 158°F
• Maximum altitude: 2,000m, 6,560ft
• Humidity (non-condensing): 80% up to 31C, 88F, decreasing linearly to 50% at 40C, 104F
• Noise: <70dB(A) at 1m

Specifications:

Dual Syringe Infusion Pump

Wide range (100,000:1) allows flow rates from a slow trickle to a steady stream


RS-232 interface lets you easily control pumps from your computer

• Max Flow Rate Per Syringe (mL/min): 147
• Linear Force (lbs): 40
• Syringe Size Accepted (Max mL): 140
• Syringe Size Accepted (Min microL): 10
• Syringe Travel Rate (mm/min): Maximum: 126.7
• Reproducibility: ±0.1%
• Accuracy: ±<1%

Pump head ideal for fast tubing changes and reduced maintenance. The design and adjustable tubing retention allow for multiple tubing sizes—change tubing without removing head from drive.

Specifications:

• Dimensions: 114 L x 64 W x 102 H (mm)
• Max Flow Rate: 2300 mL/min
• Min Flow Rate: .001 mL/min
• Tubing sizes: L/S (13, 14, 16, 17, 18, 25)
• Rollers: 3 

Pump head ideal for fast tubing changes and reduced maintenance. The design and adjustable tubing retention allow for multiple tubing sizes—change tubing without removing head from drive.

Specifications:

• Dimensions: 114 L x 64 W x 102 H (mm)
• Max Flow Rate: 2300 mL/min
• Min Flow Rate: .001 mL/min
• Tubing sizes: L/S (13, 14, 16, 17, 18, 25)
• Rollers: 3 

Description:

The Console Drives are highly featured yet easy to operate Masterflex L/S pump drives, These drives are self contained compact unites that include a drive motor and all operating controls. The keypad is laid out on a sloped front panel for ease of control and for quick and easy indication status. A digital display provides a continuous indication of flow rates, actual rpm or percentage of maximum rpm.

Specifications:

• Maximum Speed: 100 rpm
• Minimum Speed: 1.6 rpm
• Operating Temperature: 0°C to 40°C
• Storage Temperature: -10°C to 60°C
• Chemical Resistance: Exposed material is paint, plastic, aluminum, and vinyl
• Line Voltage Limits: 90 to 130 V AC, 50/60 Hz
• Dimensions (L x W x H): 11.5 x 7 x 7 in. (29.2 x 17.8 x 17.8 cm)
• Weight: 15 lbs. (6.8 kg)

Description:

An economical and versatile variable-speed drive with a wide flow range:

• Separate single-turn speed control and on/off switch with green power indicator—maintain speed setting while turning pump on/off.
• The 1/20-hp unidirectional motor (counterclockwise) has soft start and back EMF for ±5% speed control.
• Stackable painted steel housing is IP22 rated for protection from vertically falling water.
• 115 VAC models are UL and cUL listed; 230 VAC models are CE marked in compliance with European Community standards.
• 6-ft (1.8-m) line cord; 115 VAC: U.S. standard plug; 230 VAC: IEC 320/CEE22 socket—pumps are shipped with cord/plug set specific to destination country.

Specifications:

• Min RPM: 7
• Max RPM: 200
• Max. Flow Rate:1130 mL/min
• Min. Flow Rate: 0.42 mL/min
• Dimensions (L x W x H): 9” x 7” x 6” (229 x 178 x 152 mm)

Features

• Control Type: Variable-Speed Analog
• Number Of Channels: 1
• No washdown capable
• Continuous duty cycle

Specifications:

• Speed Range: 35 - 200 rpm
• Flow Rate Per Channel Range: 1.6 - 239 mL/min
• Number of Rollers: 3
• Power Consumption: 90 - 260 VAC, 50/60 Hz
• Dimensions (W x H x L): 5.25 x 4.5 x 8.5 in

Features:

• Powerful and rapid drying through injectors as well as in chamber
• Fast turnaround avoids waiting for glassware
• Increased safety with on-board storage and input of chemicals
• Economical and accurate dosing by two peristaltic pumps

Specifications:

• Washer Height: 845 mm / 33.27 in
• Washer Width: 900 mm / 35.43 in
• Washer Depth: 737 mm / 29 in
• Chamber Height: 508 mm / 20 in
• Chamber Width: 535 mm / 21 in
• Chamber Depth: 510 mm / 20 in
• Drying: HEPA filtered chamber and direct injection drying
• Total electrical power: 7 kw
• Net weight: 115 kg / 254 lbs
• Loading Height: 250 mm / 10 in
• Water Consumption: 12 L / 3.1 gal - per fill
• Heat Loss: 3,054 Btu/770 Kcal/h
• Sound Level: <65 dBa
• Steam Condenser: Standard

Features:

Ideal for situations requiring low levels of oxygen during critical isolation of your research materials.

Specifications:

• Internal Dimensions: 41"w x 28"d x 26"h, 104cm x 71cm x 66cm
• External Dimensions: 55"w x 35"d x 38"h, 140cm x 89cm x 97cm
• Volume: 17.3 cu. Ft., 489 L
• Power requirements: 120 Volts 60 Hz.
• Formed one piece clear acrylic top.
• Self-sealing quick disconnects enable the operator to change the drying train without disturbing the internal atmosphere. Matched die molded thermoset white bottom.
• Adjustable vacuum gauge on transfer chamber.
• Two vacuum pressure pumps, one each for transfer chamber and drying train.
• Four ground key cock valves for purging.
• Drying train includes polycarbonate canisters containing DesiSphereTM.
• Inner door on transfer chamber opens automatically when pressures are neutralized between main chamber and transfer chamber.
• All controls are illuminated.
• Transfer chamber is 12" long and 11" diameter (Interior Dimension).
• "Bright Light" system (40,000 hour lamp).
• Electrical outlet strip; U.L. & C.S.A. approved, hospital grade with four outlets.
• White ambidextrous Hypalon gloves.
• All clamps are adjustable to compensate for wear.

Description:

Refrigeration service pump is designed for removing air and moisture from industrial and commercial chillers. Pump includes a gas ballast valve that inhibits condensation reducing corrosion, an On/Off switch, 3-wire cord, and oil.

Specifications:

• Displacement: 7.7 cfm
• Ultimate Pressure Torr: 3 x 10-4
• Intake Male SAE Flare: 3/4
• NPT Inlet: 3/4"
• Voltage: 115/230
• Amps AC: 6.8/3.4
• Dimensions (L x H x W): 20.5” x 10.75” x 7.125”
• Hz: 60

Includes:

• Qty (2) - G1361A Agilent 1100 Series Prep Pumps
• G1315A DAD Diode Array Detector (G1314A VWD Detector also available)
• G2258A Agilent 1100 Prep Dual Loop Autosampler (Manual Injector also an option)
• G1364B AFC Automated Fraction Collector
• Computer Loaded with ChemStation
• Monitor – Mouse – Keyboard
• Cables and Manuals

G1361 Prep Pump

Features:

• Extended flow rate range
• Without changing pump heads, provides flow rates up to 100 mL/min at 400 bar
• For preparative and analytical applications with low flow rates (0.5 mL/min, upward), provides precise high-pressure binary gradient formation with low delay volume (700 uL)
• Automated seal wash using a peristaltic pump extends seal lifetime
• Pumps stop in response to column blockage or leaks
• Automated electromagnetic purge valve simplifies system setup
• Software provides solvent level control that keeps the pump from running dry

Features:

• Simple column selection with huge built-in library
• Automatic titration of buffers across a broad pH range
• Quick and easy transfer of methods to production-scale
• UNICORN method wizard High performance purification and characterization
• State-of-the-art computer-controlled pumps, UV/conductance monitors, and fraction collector
• UV-Vis detection of up to three wavelengths simultaneous

Specifications:

• Flow rate: 0.01-100 ml/min
• Operating pressure max.: 10 MPa
• Tubing i.d. (flow path): 0.75 mm
• UV wavelength: 190-700 nm
• Flow cell path length: 2 mm
• pH monitoring: 2–12
• Buffer selection: 11 buffer inlets
• Relative humidity: 10%-95% (non condensing)
• pH Stability: 1-14
• Viscosity: max 5 cP
• Multiple wavelength detection: Yes, up to 3 wavelengths
• Multiple sample injection: Yes, up to 8 samples
• Autosampler injection: Optional
• Automatic buffer preparation: BufferPrep
• Pump type: Piston pump, metering type
• Application: Purification of microgram to gram quantities of protein
• Dimensions (W x H x D): 480 x 610 x 470 mm
• Power Requirements: 100-120/220-240 VAC, 600W

Description:

The MJ Research Alpha Slide ALD-0211 Thermal Cycler is engineered to adapt to the diverse needs of modern laboratories. This thermal cycler is designed as a swappable sample-block/heat-pump assembly, capable of customizing any DNA Engine line thermal cycler. The ALD-0211 is equipped with a thermal cycler base which efficiently distributes electric power, as well as thermoelectric heat pumps and sensors which help control sample temperatures. The ALD-0211 Thermal Cycler meets NIST-traceable standards with its ability to provide outstanding temperature uniformity using multi-sensor, multi zone temperature controls. Designed for humidified chamber hybridizations and in situ procedures, the Alpha Slide ALD-0211 system thermally cycles glass microscope slides in a dual-block format, with each block accommodating up to 16 slides.

Descriptions:

The Cogent M1 system is an easy-to-use bench-top TFF system that is ideally suited for process development, scaling studies, as well as clinical trials and small-scale production. An innovative and intelligent design, the system enables an extremely low hold-up volume for maximum volume concentration and optimal product recovery. Equipped with a 10-liter tank with embedded balance, the Cogent M1 system can also run in fed-batch or diafiltration mode using an optional transfer pump, which enables the system to process up to 100 liters or more based on product and membrane filter characteristics.

Specifications:

• Filtration Area: 0.1 sq. m to 1.14 sq. m
• Minimum Working Volume: 300 mL at 20% feed pump speed
• Starting Volume: Tank volume of 10 liters
• Hold-up Volume: < 10 mL (excluding cassette)
• Process Temperature Range: 4°C to 50°C (39°F to 122°F)
• Maximum Feed Flow Rate: 4.5 L/min at 5 bar g (72.5 psi)
• Minimum Feed Flow Rate: 200 mL/min
• Maximum Operating Pressure: 5 bar g (72.5 psi)
• Maximum System Pressure: 6 bar g (86 psi) before pump shut-off
• Optional Transfer Pump Flow Rate: Tubing dependant (0.16 to 2300 mL/mn)