Used Lab Equipment

Specification:

• Detection type: Double-beam photometer
• Light source: Deuterium lamp
• Wavelength range: 190–600 nm
• Short term noise (ASTM): ±0.75×10^-5 AU at 254 nm
• Drift: 3 × 10 ^-4 AU/hr at 254 nm
• Linearity: 2 AU (5%) upper limit
• Wavelength accuracy:
• Band width: 5 nm typical
• Flow cells:
  • Standard: 14-μl volume, 10-mm cell path length and 40 bar (588 psi) pressure maximum
  • High pressure: 14-μl volume, 10-mm cell path length and 400 bar (5880 psi) pressure maximum
  • Micro: 1-μl volume, 5-mm cell path length and 40 bar (588 psi) pressure maximum
  • Semimicro: 5-μl volume, 6-mm cell path length and 40 bar (588 psi) pressure maximum
• Control and data evaluation: Agilent ChemStation for LC
• Analog outputs: Recorder/integrator: 100 mV or 1 V, output range 0.001 – 2 AU, one output
• Communications: Controller-area network (CAN), GPIB, RS-232C, APG Remote: ready, start, stop and shut-down signals, LAN optional
• Safety and maintenance: Extensive diagnostics, error detection and display (through control module and Agilent ChemStation), leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in major maintenance areas.
• GLP features: Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of lamp burn time with user-settable limits and feedback messages. Electronic records of maintenance and errors. Verification of wavelength accuracy with built-in holmium oxide filter
• Housing: All materials recyclable.

Specifications: 

• Detection type: Double-beam photometer
• Light source: Deuterium lamp
• Noise: ± 0.75 x 10 -5 AU, at 254 nm
• Drift: 3 x 10-4AU/hr, at 254 nm
• Linearity: >2 AU upper limit
• Wavelength range: 190-600 nm
• Wavelength accuracy: ± 1 nm, self-calibration with deuterium lines, verification with holmium oxide filter
• Wavelength bandwidth: 6.5 nm typical over whole wavelength range
• Maximum data rate: 55 Hz

Specifications: 

• Detection type: Double-beam photometer
• Light source: Deuterium lamp
• Noise: ± 0.75 x 10 -5 AU, at 254 nm
• Drift: 3 x 10-4AU/hr, at 254 nm
• Linearity: >2 AU upper limit
• Wavelength range: 190-600 nm
• Wavelength accuracy: ± 1 nm, self-calibration with deuterium lines, verification with holmium oxide filter
• Wavelength bandwidth: 6.5 nm typical over whole wavelength range
• Maximum data rate: 55 Hz

Specifications:

• Optical design: Dual-beam photometer
• Light source: Deuterium lamp and tungsten lamp
• Wavelength range: 190 to 900 nm
• Wavelength accuracy: ± 1 nm
• Wavelength repeatability: y: ± 0.1 nm
• Optical bandwidth: 6 nm at 254 nm

Specifications:

• Detection type: 1024-element photodiode array
• Light source: Deuterium and tungsten lamps
• Wavelength range: 190 – 950 nm
• Short term noise (ASTM) Single and Multi-Wavelength: ± 1 × 10-5AU at 254 and 750 nm
• Drift: 2 × 10-3AU/hr at 254 nm
• Linear absorbance Range: 2 AU (upper limit)
• Wavelength accuracy: ± 1 nm
• Wavelength bunching: 1 – 400 nm
• Slit width: 1, 2, 4 , 8, 16 nm
• Diode width: < 1 nm
• Flow cells
  • Standard: 13 µl volume, 10 mm cell path length and 120 bar (1760 psi) pressure maximum
  • Semi-Micro: 5 µl volume, 6 mm cell path length and 120 bar (1760 psi) pressure maximum
  • High pressure: 1.7 µl volume, 6 mm cellpath length and 400 bar (5880 psi) pressure maximum
  • 500 nano: 0.5 µl volume, 10 mm cell path length and 50 bar (725 psi) pressure maximum
• Control and data Evaluation: Agilent ChemStation for LC
• Analog outputs: Recorder/integrator: 100 mV or 1 V, output range 0.001 – 2 AU, two outputs
• Communications: Controller-area network (CAN), GPIB, RS-232C, APG Remote: ready, start, stop and shut-down signals, LAN optional
• Safety and maintenance: Extensive diagnostics, error detection and display (through control module and ChemStation), leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in major maintenance areas.
• GLP features: Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of lamp burn time with user-settable limits and feedback messages. Electronic records of maintenance and errors. Verification of wavelength accuracy with built-in holmium oxide filter

Can be sold as an individual component or as part of a complete stack

Specifications:

• Detection type: 1024-element photodiode array
• Light source: Deuterium and tungsten lamps
• Wavelength range: 190 – 950 nm
• Short term noise (ASTM) Single and Multi-Wavelength: ± 1 × 10-5AU at 254 and 750 nm
• Drift: 2 × 10-3AU/hr at 254 nm
• Linear absorbance Range: 2 AU (upper limit)
• Wavelength accuracy: ± 1 nm
• Wavelength bunching: 1 – 400 nm
• Slit width: 1, 2, 4 , 8, 16 nm
• Diode width: < 1 nm
• Flow cells
  • Standard: 13 µl volume, 10 mm cell path length and 120 bar (1760 psi) pressure maximum
  • Semi-Micro: 5 µl volume, 6 mm cell path length and 120 bar (1760 psi) pressure maximum
  • High pressure: 1.7 µl volume, 6 mm cellpath length and 400 bar (5880 psi) pressure maximum
  • 500 nano: 0.5 µl volume, 10 mm cell path length and 50 bar (725 psi) pressure maximum
• Control and data Evaluation: Agilent ChemStation for LC
• Analog outputs: Recorder/integrator: 100 mV or 1 V, output range 0.001 – 2 AU, two outputs
• Communications: Controller-area network (CAN), GPIB, RS-232C, APG Remote: ready, start, stop and shut-down signals, LAN optional
• Safety and maintenance: Extensive diagnostics, error detection and display (through control module and ChemStation), leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in major maintenance areas.
• GLP features: Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of lamp burn time with user-settable limits and feedback messages. Electronic records of maintenance and errors. Verification of wavelength accuracy with built-in holmium oxide filter

Can be sold as an individual component or as part of a complete stack

Features:

The ImageQuant LAS 4000 is a camera system for producing digital images of gel or membrane samples or films. It is used together with the ImageQuant LAS 4000 Control Software to:

• Expose chemiluminescent samples or membranes.

• Expose fluorescent samples using epi (incident) or trans (transmitted) light sources, for example gels stained by ethidium bromide (EtBr). The ImageQuant LAS 4000 can be supplied with NIR, Red, Green, Blue and UV epi lights.

• Expose dye-stained gels and membranes or films using epi or trans illumination.

• Expose a sample repeatedly, incrementally or by programming exposure schemes.

Specifications:

• CCD: 3 200 000 pixels (Fujifilm super CCD
• Cooling temperature: -25°C
• Exposure time: 1/100 seconds to 2 hours (Images can be continuously exposed for up to 30 hours using ImageQuant LAS 4000 Control Software.)
• Lens: High-sensitivity lens F0.85 43 mm, Wide view lens F1.8 24 mm
• Number of gradations:

Recorded image: 16 bit

Focusing: 8 bit

Includes:

• Blue Laser Module
• Laptop w/ Image Quant and Scan Control Software loaded on computer
• All Necessary Cables, Cords and Manuals

Features:

• Versatile system platform, handles gel sandwiches, agarose and polyacrylamide gels, membranes, microplates, and even microarrays.
• Powerful excitation sources and innovative high-quality confocal optics allow for the sensitive detection of low-abundance targets.
• Red-, green-, and blue-excitation wavelengths and a wide choice of emission filters enable imaging of an extensive variety of fluorophores.
• Automated four-color fluorescence scanning allows multiplexing of multiple targets in the same sample ensuring accuracy of analysis, increasing throughput, and saving time.
• Storage phosphor technology delivers high-resolution imaging and accurate quantitation of ³H, ¹⁴C, ¹²⁵I, ³²P, ³³P, ³⁵S, and other sources of ionizing radiation.
• Highly sensitive optics enable direct chemiluminescent imaging without intermediate exposure to films or screens.
• Provides optimized detection of Cy2, Cy3, and Cy5 CyDye DIGE Fluor minimal and saturation dyes, enabling visualization of up to three differently labeled samples on a single gel.
• Exceptional signal-to-noise increases the number of statistically significant differences detected.
• Consistent point-light illumination produces high-quality uniform images and reduces photo-bleaching.
• Gels are scanned between glass plates, preventing drying and shrinkage and allowing further running and rescanning if required.

Variable mode laser scanner providing both versatile and flexible imaging for precise quantitation of proteins, nucleic acids, and other biomolecules. The system accommodates four automated filters. Filters are easily accessed and exchanged without tools for attaining optimal imaging conditions. Typhoon FLA 9500 comes equipped with both bi-alkali and multialkali photomultiplier tubes (PMT). This combination provides excellent detection over a very broad spectrum. Each PMT is selected for optimal response to the detected emission wavelength.

Specifications:

• Temperature Range: 15° to 30°C
• Dynamic Range: 5 Orders of Magnitude
• Detection Modes: Fluorescence, Phosphorimaging, Digitization, and Chemiluminescence
• Bit Depth: 16-bit
• Operating Humidity: 20 to 70%
• Standard Filters: IP (Phosphorimaging), LPB (510LP), LPG (575LP), LPR (665LP), LPR-Ch2 (665LP), BPB1 (530DF20), and BPG1 (570DF20) 

The Typhoon instrument is a variable-mode imager that produces digital images of radioactive, fluorescent, or chemiluminescent samples. The Typhoon instrument is available in several models. The Typhoon Trio instrument contains three internal lasers (blue, green, and red).

Includes:

• Red, Blue, Green Laser Modules Built in
• Image Quant and Scan Control Software loaded on computer
• All Necessary Cables, Cords and Manuals

For DNA, RNA, and protein samples, users can choose from:

• Storage phosphor autoradiography
• Direct green (532 nm) excited fluorescence
• Direct red (633 nm) excited fluorescence
• Direct blue (488 nm) excited fluorescence
• Chemiluminescence

Features:

• When one of the five scanning modes is selected, the appropriate optical components are automatically activated.
• Typhoon imagers scan mounted and unmounted storage phosphor screens, gels and blots up to 35 x 43 cm as well as microarrays.
• Typhoon imagers exhibit outstanding linearity and quantitative  accuracy, and include ImageQuant TL Image Analysis Software.
• Typhoon imagers are fully optimized as part of the Ettan DIGE system, and seamless integration with DeCyder Differential Analysis Software
• is ensured for all models.
• Special tray templates that are part of the latest scanner control software and new optional Gel Alignment Guides add higher throughput and ease of handling 2-D gels run on Ettan DALT and SE600.

The Typhoon instrument is a variable-mode imager that produces digital images of radioactive, fluorescent, or chemiluminescent samples. The Typhoon instrument is available in several models. The Typhoon Trio instrument contains three internal lasers (blue, green, and red).

Includes:

• Red, Blue, Green Laser Modules Built in
• Image Quant and Scan Control Software loaded on computer
• All Necessary Cables, Cords and Manuals

For DNA, RNA, and protein samples, users can choose from:

• Storage phosphor autoradiography
• Direct green (532 nm) excited fluorescence
• Direct red (633 nm) excited fluorescence
• Direct blue (488 nm) excited fluorescence
• Chemiluminescence

Features:

• When one of the five scanning modes is selected, the appropriate optical components are automatically activated.
• Typhoon imagers scan mounted and unmounted storage phosphor screens, gels and blots up to 35 x 43 cm as well as microarrays.
• Typhoon imagers exhibit outstanding linearity and quantitative  accuracy, and include ImageQuant TL Image Analysis Software.
• Typhoon imagers are fully optimized as part of the Ettan DIGE system, and seamless integration with DeCyder Differential Analysis Software
• is ensured for all models.
• Special tray templates that are part of the latest scanner control software and new optional Gel Alignment Guides add higher throughput and ease of handling 2-D gels run on Ettan DALT and SE600.

The ACQUITY UPLC TUV Detector is a tunable, dual wavelength ultraviolet/visible (UV/Vis) detector that offers optimal linearity, resolution, and sensitivity for UPLC/UV separations.  It features uniquely designed, patented, light-guiding flow cell technology, low-noise performance (6 μAU), and support for data rates up to 80 Hz.  The ACQUITY UPLC TUV Detector, coupled with our innovative ACQUITY UPLC Column chemistries and separations modules, leverages ultra-low dwell volume and low-noise, high-speed detection to bring productivity, sensitivity, and resolution that are unprecedented in HPLC techniques being used in the laboratory today.

Specifications:

• Wavelength range: 190 to 700 nm
• Wavelength accuracy: ±1 nm
• Linearity range: Deviation at 2.5 AU ≤5%, propylparaben, at 257 nm
• Baseline noise:6 x 10^-3 AU, at 230 nm, 10 mm shunt cell, 1.0 second filter time constant
• Drift: ≤5.0 x 10^-4 AU/hour/°C at 230 nm
• Sampling rate: Up to 80 points/s
• Unattended operation: Leak sensors, full diagnostic data captured through console software
• Light source: Prealigned, intelligent technology Deuterium lamp
• Flow cell design: Light-guiding UPLC flow cell with intelligent chip technology
• Path length: 10 mm (analytical flow cell)
• Cell volume: 500 nL (analytical flow cell)
• Pressure limit: 1000 psi (all flow cells)
• Wetted materials: 316 stainless steel, fused silica, Teflon AF, PEEK (analytical flow cell)
• Optical bandwidth: 5 nm

The Agilent 1100 Series G1315 Diode Array Detector is designed for the maximum optical performance. Flexible slit setting from fine bands to highest sensitivity, with settings of 1 nm the fine structure of benzene can be revealed - even at 0.7mAUFS. A broad slit of 8 or 16nm can be chosen to minimize baseline noise thus enhancing sensitivity. System specifications include:

Specifications:

• Wavelength range: 190-950 nm
• Light source: Deuterium and tungsten lamps
• Detection type: 1024 - element photodiode array
• Short term noise (ASTM) single & mult-wavelength: ± 1° x 10-5 AU at 254 and 750 nm
• Drift: 2° x 10-3 AU / hr at 254 nm
• Linear absorbance range: > 2 AU (upper limit)
• Wavelength accuracy: ± 1 nm
• Wavelength bunching: 1 - 400 nm
• Diode width: < 1 nm
• Control and data evaluation: Agilent Chemstation for LC
• Slit width: 1, 2, 4, 8, 16 nm

Can be sold as an individual component or as part of a complete stack

The Agilent 1100 Series G1315 Diode Array Detector is designed for the maximum optical performance. Flexible slit setting from fine bands to highest sensitivity, with settings of 1 nm the fine structure of benzene can be revealed - even at 0.7mAUFS. A broad slit of 8 or 16nm can be chosen to minimize baseline noise thus enhancing sensitivity. System specifications include:

Specifications:

• Wavelength range: 190-950 nm
• Light source: Deuterium and tungsten lamps
• Detection type: 1024 - element photodiode array
• Short term noise (ASTM) single & mult-wavelength: ± 1° x 10-5 AU at 254 and 750 nm
• Drift: 2° x 10-3 AU / hr at 254 nm
• Linear absorbance range: > 2 AU (upper limit)
• Wavelength accuracy: ± 1 nm
• Wavelength bunching: 1 - 400 nm
• Diode width: < 1 nm
• Control and data evaluation: Agilent Chemstation for LC
• Slit width: 1, 2, 4, 8, 16 nm

Can be sold as an individual component or as part of a complete stack

The Agilent 1100 Series G1315 Diode Array Detector is designed for the maximum optical performance. Flexible slit setting from fine bands to highest sensitivity, with settings of 1 nm the fine structure of benzene can be revealed - even at 0.7mAUFS. A broad slit of 8 or 16nm can be chosen to minimize baseline noise thus enhancing sensitivity. System specifications include:

Specifications:

• Wavelength range: 190-950 nm
• Light source: Deuterium and tungsten lamps
• Detection type: 1024 - element photodiode array
• Short term noise (ASTM) single & mult-wavelength: ± 1° x 10-5 AU at 254 and 750 nm
• Drift: 2° x 10-3 AU / hr at 254 nm
• Linear absorbance range: > 2 AU (upper limit)
• Wavelength accuracy: ± 1 nm
• Wavelength bunching: 1 - 400 nm
• Diode width: < 1 nm
• Control and data evaluation: Agilent Chemstation for LC
• Slit width: 1, 2, 4, 8, 16 nm

Can be sold as an individual component or as part of a complete stack